Tolga Kuşkun

Dr. Tolga Kuşkun

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
Ali KASALAli KASAL
Ali KASAL
TKTolga Kuşkun
Tolga Kuşkun
JERZY SMARDZEWSKIJERZY SMARDZEWSKI
JERZY SMARDZEWSKI
Studies on the application of auxetic metamaterials and structures in furniture joints are very limited. However, they have huge potential for use in ready-to-assemble furniture. This study aimed to design and produce different types of auxetic dowels in 3D printing technology, and experimentally and numerically analyze the withdrawal strength of these dowels. In the scope of the study, 24 auxetic dowels with different types and size of inclusions, different diameter of holes, and a non-auxetic reference dowel were designed and produced with appropriate muffs. Dowels were 3D printed from polyamide (PA12). Poisson’s ratios, withdrawal strength, contact pressures, and friction coefficients of dowels were determined theoretically by means of numerical analyses and real static compression tests. After the pre-production of dowels, the dowels with triangular inclusions have not been found to have sufficient strength and stiffness. Withdrawal strength of dowels decreased as the size of inclusions is decreased, or dowel hole diameter is increased. Furthermore, contact pressures and stresses in auxetic dowels were considerably lower than non-auxetic dowels under the withdrawal force.

23 June 2023 in Materials
Verified
Journal Article
Open access
PDF file
Ali KASALAli KASAL
Ali KASAL
JERZY SMARDZEWSKIJERZY SMARDZEWSKI
JERZY SMARDZEWSKI
TKTolga Kuşkun
Tolga Kuşkun
EGErsan Güray
Ersan Güray
Tests were carried out to develop and manufacture various types of auxetic dowels using 3D printing technology. These dowels were then used to connect L-type corner joint specimens for case furniture, and their strength and stiffness were analyzed through experimental, theoretical, and numerical means. In the scope of the study, eight different types of auxetic dowels including two inclusion types, two inclusion sizes, and two dowel hole diameters, as well as a reference non-auxetic dowel, were designed. Accordingly, a total of 180 specimens that included 10 replications for each group were tested; 90 were tested under tension and the remaining 90 were tested under compression. The results demonstrated that the assembly force required for the corner joints connected with auxetic dowels was significantly lower compared to non-auxetic dowels. Furthermore, the numerical and theoretical analyses yielded similar outcomes in this study. Both analyses revealed that the dowels used to connect the corner joints experienced substantial stresses during mounting and bending, ultimately leading to their failure. Upon concluding the test results, it was observed that the corner joints connected with dowels featuring rectangular inclusions exhibited superior performance when compared to those with triangular inclusions. In light of these findings, it can be concluded that further enhancements are necessary for auxetic dowels with rectangular inclusions before they can be utilized as alternative fasteners for traditional dowels.

23 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
ŁKŁukasz Krzyżaniak
Łukasz Krzyżaniak
TKTolga Kuşkun
Tolga Kuşkun
Ali KASALAli KASAL
Ali KASAL
JERZY SMARDZEWSKIJERZY SMARDZEWSKI
JERZY SMARDZEWSKI
This study aimed to numerically and experimentally analyze the effects of internal mounting forces and selected materials on the stiffness and bending moment capacity of L-type corner joints connected with novelty-designed 3D printed fasteners. The experiments were carried out using medium-density fiberboard, high-density fiberboard, beech plywood, particleboard, and beech (Fagus silvatica L.) wood. The results showed that the joints made of beech wood were characterized by the largest bending moment capacity (12.34 Nm), while the worst properties were shown by particleboard (2.18 Nm). The highest stiffness was demonstrated by plywood joints (6.56 kNm/rad), and the lowest by particleboard (0.42 kNm/rad). Experimental studies have reasonably verified the results of numerical calculations. The test results confirmed that the geometry of new fasteners promotes the mounting forces under the assembly of the joints. It was shown that the higher the density of the materials, the greater the value of the mounting forces (164 N–189 N).

2 April 2023 in Materials
Verified
Journal Article
Open access
PDF file
TKTolga Kuşkun
Tolga Kuşkun
Ali KASALAli KASAL
Ali KASAL
GÇGökhan Çağlayan
Gökhan Çağlayan
ECErkan Ceylan
Erkan Ceylan
MBMurat Bulca
Murat Bulca
JERZY SMARDZEWSKIJERZY SMARDZEWSKI
JERZY SMARDZEWSKI
In this study, the aim was to optimize the cross-sectional geometry of auxetic dowels for furniture joints. For this purpose, two different sizes of auxetic dowels were chosen, one for frame- and the other for panel-type furniture joints for designing the cross-sectional geometry. Auxetic patterns that are created on the cross-sectional area cause deficiency of the materials, and this phenomenon decreases the modulus of elasticity (MOE) and increases the member stress. Accordingly, maximum MOE values and minimum Poisson’s ratio levels were determined for the optimum strength-auxetic behavior relation by means of a Monte Carlo method. Furthermore, Poisson’s ratio of the optimized dowel’s cross-section was confirmed with experimental tests, numerical analyses and analytical calculations. As a result, Poisson’s ratio values were obtained as negative values and confirmed, which means the dowels designed in this study had auxetic behavior. In conclusion, it could be said that studies should be conducted on the performance of auxetic dowels in both frame and panel furniture joints.

2 November 2017 in BioResources
Verified
Journal Article
Open access
PDF file
HKHalil Kılıç
Halil Kılıç
Ali KASALAli KASAL
Ali KASAL
TKTolga Kuşkun
Tolga Kuşkun
MAMehmet Acar
Mehmet Acar
YEYUSUF ZIYA ERDIL
YUSUF ZIYA ERDIL
Effect of Tenon Size on Static Front to Back Loading Performance of Wooden Chairs in Comparison with Acceptable Design Loads

15 May 2024 in Wood Material Science & Engineering
Verified
Journal Article
Closed access
MUMesut Uysal
Mesut Uysal
TKTolga Kuşkun
Tolga Kuşkun
JERZY SMARDZEWSKIJERZY SMARDZEWSKI
JERZY SMARDZEWSKI
Ali KASALAli KASAL
Ali KASAL
EHEva Haviarova
Eva Haviarova