Ali KASAL

Prof. Dr. Ali KASAL

Muğla University, Muğla, Turkey (Türkiye)
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 November 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YLyan Liu
yan Liu
Wengang HuWengang Hu
Wengang Hu
Ali KASALAli KASAL
Ali KASAL
YEYUSUF ZIYA ERDIL
YUSUF ZIYA ERDIL
Furniture as a functional object must satisfy both artistic and scientific requirements. In particular, ergonomic factors are very important in furniture design in terms of human health and productivity. To make furniture designs at the ideal intersection of science and art, it is necessary to approach furniture design with a scientific systematic. Accordingly, this paper summarizes and analyzes the current state of biomechanics in ergonomic furniture design, covering an overview of the biomechanics utilized in different types of furniture design, biomechanical analysis, and testing methods. In the conclusion of the study, the literature analysis identifies the key topics and areas of future exploration regarding the use of biomechanics in ergonomic furniture design. The findings of the review indicate that (1) the primary studies on biomechanics used in furniture design concentrate on special furniture, such as wheelchairs and transportation vehicle seats, with minimal investigation performed on common furniture; (2) mechanical analysis, experimental testing, and computer-aided ergonomics represent the main techniques applied in furniture design biomechanics; (3) the reliability of biomechanics used in furniture design needs to be improved due to the lack of fundamental parameters of the muscles and skeleton of the human body; and (4) more attention should be paid to the use of biomechanics in the design of common furniture, such as household and office furniture, which affects people’s health and comfort. The scientific and rational application of biomechanics should be integrated into ergonomic furniture design to promote healthy living and enhance work efficiency.

5 May 2016 in BioResources
Verified
Journal Article
Open access
PDF file
Ali KASALAli KASAL
Ali KASAL
JERZY SMARDZEWSKIJERZY SMARDZEWSKI
JERZY SMARDZEWSKI
TKTolga Kuşkun
Tolga Kuşkun
YEYUSUF ZIYA ERDIL
YUSUF ZIYA ERDIL
Numerical Analyses of Various Sizes of Mortise and Tenon Furniture Joints

24 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
Ali KASALAli KASAL
Ali KASAL
TKTolga Kuşkun
Tolga Kuşkun
JERZY SMARDZEWSKIJERZY SMARDZEWSKI
JERZY SMARDZEWSKI
Studies on the application of auxetic metamaterials and structures in furniture joints are very limited. However, they have huge potential for use in ready-to-assemble furniture. This study aimed to design and produce different types of auxetic dowels in 3D printing technology, and experimentally and numerically analyze the withdrawal strength of these dowels. In the scope of the study, 24 auxetic dowels with different types and size of inclusions, different diameter of holes, and a non-auxetic reference dowel were designed and produced with appropriate muffs. Dowels were 3D printed from polyamide (PA12). Poisson’s ratios, withdrawal strength, contact pressures, and friction coefficients of dowels were determined theoretically by means of numerical analyses and real static compression tests. After the pre-production of dowels, the dowels with triangular inclusions have not been found to have sufficient strength and stiffness. Withdrawal strength of dowels decreased as the size of inclusions is decreased, or dowel hole diameter is increased. Furthermore, contact pressures and stresses in auxetic dowels were considerably lower than non-auxetic dowels under the withdrawal force.

23 June 2023 in Materials
Verified
Journal Article
Open access
PDF file
Ali KASALAli KASAL
Ali KASAL
JERZY SMARDZEWSKIJERZY SMARDZEWSKI
JERZY SMARDZEWSKI
TKTolga Kuşkun
Tolga Kuşkun
EGErsan Güray
Ersan Güray
Tests were carried out to develop and manufacture various types of auxetic dowels using 3D printing technology. These dowels were then used to connect L-type corner joint specimens for case furniture, and their strength and stiffness were analyzed through experimental, theoretical, and numerical means. In the scope of the study, eight different types of auxetic dowels including two inclusion types, two inclusion sizes, and two dowel hole diameters, as well as a reference non-auxetic dowel, were designed. Accordingly, a total of 180 specimens that included 10 replications for each group were tested; 90 were tested under tension and the remaining 90 were tested under compression. The results demonstrated that the assembly force required for the corner joints connected with auxetic dowels was significantly lower compared to non-auxetic dowels. Furthermore, the numerical and theoretical analyses yielded similar outcomes in this study. Both analyses revealed that the dowels used to connect the corner joints experienced substantial stresses during mounting and bending, ultimately leading to their failure. Upon concluding the test results, it was observed that the corner joints connected with dowels featuring rectangular inclusions exhibited superior performance when compared to those with triangular inclusions. In light of these findings, it can be concluded that further enhancements are necessary for auxetic dowels with rectangular inclusions before they can be utilized as alternative fasteners for traditional dowels.

23 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
ŁKŁukasz Krzyżaniak
Łukasz Krzyżaniak
TKTolga Kuşkun
Tolga Kuşkun
Ali KASALAli KASAL
Ali KASAL
JERZY SMARDZEWSKIJERZY SMARDZEWSKI
JERZY SMARDZEWSKI
This study aimed to numerically and experimentally analyze the effects of internal mounting forces and selected materials on the stiffness and bending moment capacity of L-type corner joints connected with novelty-designed 3D printed fasteners. The experiments were carried out using medium-density fiberboard, high-density fiberboard, beech plywood, particleboard, and beech (Fagus silvatica L.) wood. The results showed that the joints made of beech wood were characterized by the largest bending moment capacity (12.34 Nm), while the worst properties were shown by particleboard (2.18 Nm). The highest stiffness was demonstrated by plywood joints (6.56 kNm/rad), and the lowest by particleboard (0.42 kNm/rad). Experimental studies have reasonably verified the results of numerical calculations. The test results confirmed that the geometry of new fasteners promotes the mounting forces under the assembly of the joints. It was shown that the higher the density of the materials, the greater the value of the mounting forces (164 N–189 N).

1 February 2021 in Maderas. Ciencia y Tecnología
Verified
Journal Article
Open access
PDF file
ECErkan Ceylan
Erkan Ceylan
EGErsan Güray
Ersan Güray
Ali KASALAli KASAL
Ali KASAL
Tests were carried out to investigate the cyclic loading performance of chairs constructed of Scotch pine (Pinus sylvestris) and Oriental beech (Fagus orientalis). Totally, 30 real size chairs were constructed and assembled with polyvinyl acetate adhesive. Chairs were tested under 3 cyclic loading directions; namely, front to back, back to front, and backrest according to American Library Association (ALA) specifications, and obtained loading performances of chairs were crosschecked with allowable design load levels. Additionally, specimens were analyzed as structures by using the finite element method in order to obtain axial, shear, and bending stresses acting on each member under loadings and compare these values with design stresses. As a result, it was concluded that finite element method analyses achieve reasonable estimates for strength performances and failure behaviors of chairs. Depending on allowable design loads by American Library Association; chairs constructed of beech could meet the medium service for front to back and back to front loading, while heavy service for backrest loading. In the case of pine chairs; they could meet the medium service for front to back and back to front loading, while light service for backrest loading.