The article presents the results of experimental study on the effect of additives of silicon oxide nanoparticles, as well as single-walled and multi-walled carbon nanotubes on the colloidal stability and thermal degradation process of hydrocarbon-based drilling fluids. Such a comprehensive study of hydrocarbon-based drilling fluids was carried out for the first time. The effect of the concentration and size of silicon oxide nanoparticles, as well as the type and concentration of nanotubes on the colloidal stability of drilling fluids during thermal aging tests at different temperatures, was investigated. The nanoparticle size varied from 18 to 70 nm, and the concentration ranged from 0.25 to 2 wt.%. Single-walled and multi-walled nanotubes were studied, whose concentration varied from 0.01 to 0.5 wt.%. The thermal aging temperature varied from 30 to 150 °C. According to the results of the investigation, it was shown that the temperature stability of hydrocarbon-based drilling fluids can be significantly improved by adding the above substances. At the same time, it was shown that the use of single-walled nanotubes for thermal stabilization of drilling fluids was several times more effective than the use of multi-walled nanotubes, and tens of times more effective than the use of spherical silicon oxide nanoparticles.
A series of experiments have been carried out on the flooding of microfluidic chips simulating a homogeneous porous structure with various displacement fluids. Water and polyacrylamide polymer solutions were used as displacement fluids. Three different polyacrylamides with different properties are considered. The results of a microfluidic study of polymer flooding showed that the displacement efficiency increases significantly with increasing polymer concentration. Thus, when using a 0.1% polymer solution of polyacrylamide grade 2540, a 23% increase in the oil displacement efficiency was obtained compared to water. The study of the effect of various polymers on the efficiency of oil displacement showed that the maximum efficiency of oil displacement, other things being equal, can be achieved using polyacrylamide grade 2540, which has the highest charge density among those considered. Thus, when using polymer 2515 with a charge density of 10%, the oil displacement efficiency increased by 12.5% compared to water, while when using polymer 2540 with a charge density of 30%, the oil displacement efficiency increased by 23.6%.
Wetting hysteresis is the most important characteristic of microfluidic chips for modeling multiphase flows in rocks, including for oil production problems. Plasma modification of surface wetting characteristics is well studied, but there is a problem of stabilizing the resulting surface for use in a liquid hydrocarbon media. In this work, a simple and accessible technology for modifying the surface of PDMS and glass using a dielectric barrier discharge in a chamber based on the d’Arsonval apparatus has been developed. The surface wetting hysteresis for PDMS and glass was studied as a function of the plasma treatment time. It is shown that with the help of plasma treatment it is possible to change the wetting angles of the walls of microfluidic chips in a very wide range, thereby simulating the conditions of both hydrophobic and hydrophilic rocks. At the same time, PDMS has the widest possible range of changes in the wetting angle; the advancing contact angle decreases from 120° to 10°; receding contact angle—from 70° to 0° during plasma treatment. It has been shown that plasma treatment of a microfluidic chip, together with a 30 min primary extraction with oil and salt water, leads to a significant change in the wetting characteristics of its surface. This in total leads to an increase in the oil displacement efficiency from the chip by about 10%. In general, the results of the study showed that plasma surface treatment for the hydrophilization of microfluidic chips is a simple and affordable technology for controlling the wetting characteristics of microfluidic chips. PDMS in this case is a promising material.
Increasing the efficiency of hydrocarbon field development is an important issue. One of the methods for increasing oil recovery is the injection of aqueous solutions of polymers. Although this method has been known and used for quite some time, further systematic research is needed to further improve its effectiveness. In this work, systematic computational studies of the features of oil displacement by aqueous polymer solutions from a naturally fractured structure were carried out. Direct numerical modeling of a two-phase immiscible flow in the process of displacing oil from a natural fracture structure using solutions of anionic polymers based on polyacrylamide was carried out. Aqueous solutions of three different polymers were considered, the concentrations of which varied from 0 to 0.1%, and the molecular weights were from 10 to 20 mln c.u. The rheological properties of polymers and their wetting characteristics have been previously studied in laboratory experiments. A distinctive feature of the polymers considered was the non-Newtonian nature of their aqueous solutions even at low concentrations. To take these processes into account, the computational technique has been extended to the case of non-Newtonian rheology for immiscible two-phase flow in one of the media. During numerical simulations, the effect of the concentration of polymers, their molecular weight, and charging density on the flow regimes in a fractured reservoir have been investigated systematically at various crude oil viscosities. It has been shown that the use of a 0.1% aqueous solution of polyacrymalide can increase the oil-recovery factor by 1.8 times. It has been established that, with an increase in the molecular weight and surface charge density of the polymer, the efficiency of its use for enhancing oil recovery increases. With an increase in the viscosity of the displaced oil, the effect of using the injection of the considered polymers also increases. The data obtained in this work can be used to further improve polymer-flooding technologies for oil fields.
This article presents the results of experimental studies examining the effectiveness of low-concentration nanoemulsions for enhanced oil recovery (EOR). The maximum volume concentration of diesel fuel in the emulsions did not exceed 1% by volume. The volume concentration of the emulsifier ranged from 0.05% to 0.4%. A method for preparing stable nanoemulsions was developed. The colloidal stability, viscosity, interfacial tension, wettability, and capillary imbibition rate of low-concentration nanoemulsions were studied. Filtration experiments were conducted to study oil displacement on microfluidic chips simulating a porous medium and core samples. This is the first systematic study of the properties of nanoemulsions containing diesel fuel. It was demonstrated that the developed emulsions have high potential for EOR. It was shown that increasing the emulsifier concentration reduces the contact angle from 35 to 16 degrees and halves the surface tension coefficient. Experiments studying the capillary imbibition of oil-saturated cores with nanoemulsions also confirmed their ability to reduce interfacial tension and improve rock wettability. Oil displacement efficiency during capillary imbibition increases by 22%. Filter tests on microfluidic chips and core samples confirmed the high efficiency of the developed nanoemulsions. Increasing the emulsifier concentration in the emulsion to 0.4% increases the displacement efficiency from 32% for water displacement to 57% for nanoemulsion displacement. Core tests showed that additional injection of nanoemulsions significantly increases the oil displacement efficiency by 10–14%, depending on the emulsifier concentration in the nanoemulsion. It was also established that the use of an aqueous solution of an emulsifier without a hydrocarbon phase does not provide such a significant increase in the displacement coefficient as in the emulsion composition.