Many efforts have focused on the adsorption of metals from contaminated water by microbes. Synechococcus PCC7002, a major marine cyanobacteria, is widely applied to remove metals from the ocean’s photic zone. However, its ability to adsorb cesium (Cs) nuclides has received little attention. In this study, the biosorption behavior of Cs(I) from ultrapure distilled water by living Synechococcus PCC7002 was investigated based on kinetic and isotherm studies, and the biosorption mechanism was characterized by Fourier-transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectrometry, and three-dimensional excitation emission matrix fluorescence spectroscopy. Synechococcus PCC7002 showed extremely high tolerance to Cs ions and its minimal inhibitory concentration was 8.6 g/L. Extracellular polymeric substances (EPS) in Synechococcus PCC7002 played a vital role in this tolerance. The biosorption of Cs by Synechococcus PCC7002 conformed to a Freundlich-type isotherm model and pseudo-second-order kinetics. The binding of Cs(I) was primarily attributed to the extracellular proteins in EPS, with the amino, hydroxyl, and phosphate groups on the cell walls contributing to Cs adsorption. The biosorption of Cs involved two mechanisms: Passive adsorption on the cell surface at low Cs concentrations and active intracellular adsorption at high Cs concentrations. The results demonstrate that the behavior and mechanism of Cs adsorption by Synechococcus PCC7002 differ based on the Cs ions concentration.

Metallophytes microbiota play a key role in plant growth and resistance to heavy metal stress. Comparing to the well-studied single or some specific plant growth-promoting (PGP) bacterial strains, our current understanding of the structural and functional variations of microbiome of metallophytes is still limited. Here, we systematically investigated the endophytic and rhizosphere bacterial community profiles of a metallophyte Commelina communis growing in different Cu-polluted soils by high-throughput sequencing technology. The results showed that the rhizosphere communities of C. communis exhibited a much higher level of diversity and richness than the endosphere communities. Meanwhile, shifts in the bacterial community composition were observed between the rhizosphere and endosphere of C. communis, indicating plant compartment was a strong driver for the divergence between rhizosphere and endosphere community. Among the environmental factors, soil Cu content, followed by OM, TP and TN, played major roles in shaping the bacterial community structure of C. communis. At the highly Cu-contaminated site, Pseudomonas and Sphingomonas were the predominant genera in the endophytic and rhizospheric bacterial communities, respectively, which might enhance copper tolerance as PGP bacteria. In summary, our findings will be useful to better understand metallophyte–microbe interactions and select suitable bacterial taxa when facilitating phytoremediation.

Some special silicate particles as additives in lubricating oil have shown a certain self-repairing function for the rubbing pairs of industrial equipment in recent R&D of extreme pressure antiwear additives. This article introduces an investigation on the regenerated layer on the worn surface of a practical cylinder liner lubricated by lubricating oil with a silicate additive using some advanced techniques like transmission electron microscopy (TEM), atomic force microscopy (AFM), nano-hardness tester, scanning electron microscopy (SEM), auger electron spectroscopy (AES), and Raman spectroscopy. The basic formula of the mineral in the silicate additive is Al₄[Si₄O₁₀](OH)₄. Through some macro- and microanalyses, it was found that the silicate additive showed an obvious improving effect on their friction surface and self-repairing function. The roughness of the worn surface could be decreased greatly to several tens of nanometers, and its hardness was still above 10 GPa. The worn surface with some pits and cracks had been covered by a transparent regenerated layer, and the wear of cylinder liners was maintained at almost zero-wear level on average. The mechanism of the self-repairing function was approached. It was revealed that the silicate additive was acting as a catalyst to promote a series of complex tribochemical reactions to form a regenerated layer with amorphous carbon structure on the worn surface under high-friction temperature and pressure in the friction and wear process.

Silicon nitride is a bioceramic with great potential, and multiple studies have demonstrated its biocompatibility and antibacterial properties. In this study, silicon nitride was prepared by a microwave sintering technique that was different from common production methods. SEM and pore distribution analysis revealed the microstructure of microwave-sintered silicon nitride with obvious pores. Mechanical performance analysis shows that microwave sintering can improve the mechanical properties of silicon nitride. The CCK-8 method was used to demonstrate that microwave-sintered silicon nitride has no cytotoxicity and good cytocompatibility. From SEM and CLSM observations, it was observed that there was good adhesion and cross-linking of cells during microwave-sintered silicon nitride, and the morphology of the cytoskeleton was good. Microwave-sintered silicon nitride has been proven to be non-cytotoxic. In addition, the antibacterial ability of microwave-sintered silicon nitride against Staphylococcus aureus and Escherichia coli was tested, proving that it has a good antibacterial ability similar to the silicon nitride prepared by commonly used processes. Compared with silicon nitride prepared by gas pressure sintering technology, microwave-sintered silicon nitride has excellent performance in mechanical properties, cell compatibility, and antibacterial properties. This indicates its enormous potential as a substitute material for manufacturing bone implants.

As arsenopyrite is a typical arsenic-bearing sulfide ore, the biooxidation process of arsenopyrite is of great significance for the extraction of gold from arsenic-bearing gold ores and the generation of arsenic-bearing acid mine drainage. During the biooxidation of arsenopyrite, a large amount of arsenic is produced, which inhibits the growth and metabolism of microorganisms and thus affects the extraction of gold from arsenic-bearing gold ores. Therefore, the screening and enrichment of microorganisms with high arsenic resistance have become important aspects in the study of arsenopyrite biooxidation. As described in this paper, through arsenic acclimation, the maximum arsenic tolerance concentration of Acidithiobacillus ferriphilus QBS 3 isolated from arsenic-containing acid mine drainage was increased to 80 mM As(Ⅲ) and 100 mM As(V). Microorganisms with high arsenic resistance showed better bioleaching performance for arsenopyrite. After 18 days of bioleaching, the leaching rate of arsenopyrite reached 100% at a pulp concentration of 0.5%, and after 30 days of bioleaching, the leaching rate of arsenopyrite was 79.96% at a pulp concentration of 1%. Currently, research on arsenopyrite mainly focuses on the control and optimization of environmental conditions, but there have been few studies on the biooxidation process of arsenopyrite at the protein and gene levels. Therefore, combining the results of a one-month bioleaching experiment on arsenopyrite by A. ferriphilus QBS 3 and the analysis of arsenic resistance genes, a bioleaching model of arsenopyrite was constructed, which laid an experimental basis and theoretical foundation for improving the gold recovery rate from refractory arsenic-bearing ores and exploring the arsenic resistance mechanism of microorganisms during the arsenopyrite leaching process.