Jiajun Liu

Jiajun Liu

Auto-generated profile, based on publicly available information

Jiajun Liu

Department of Engineering Mechanics, Tsinghua University, 12442 Beijing China

Research Focus & Metrics

Academic Career Length

34Years (1993-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 1998 in Wear
Verified
Journal Article
Closed access
XZXing-Zhong Zhao
Xing-Zhong Zhao
JLJia-Jun Liu
Jia-Jun Liu
TFT.E Fischer
T.E Fischer

26 February 2010 in Tribology Transactions
Verified
Journal Article
Closed access
Wen YueWen Yue
Wen Yue
CWChengbiao Wang
Chengbiao Wang
Yuandong LiuYuandong Liu
Yuandong Liu
HHHaipeng Huang
Haipeng Huang
QWQingfeng Wen
Qingfeng Wen
JLJiajun Liu
Jiajun Liu
Some special silicate particles as additives in lubricating oil have shown a certain self-repairing function for the rubbing pairs of industrial equipment in recent R&D of extreme pressure antiwear additives. This article introduces an investigation on the regenerated layer on the worn surface of a practical cylinder liner lubricated by lubricating oil with a silicate additive using some advanced techniques like transmission electron microscopy (TEM), atomic force microscopy (AFM), nano-hardness tester, scanning electron microscopy (SEM), auger electron spectroscopy (AES), and Raman spectroscopy. The basic formula of the mineral in the silicate additive is Al4[Si4O10](OH)4. Through some macro- and microanalyses, it was found that the silicate additive showed an obvious improving effect on their friction surface and self-repairing function. The roughness of the worn surface could be decreased greatly to several tens of nanometers, and its hardness was still above 10 GPa. The worn surface with some pits and cracks had been covered by a transparent regenerated layer, and the wear of cylinder liners was maintained at almost zero-wear level on average. The mechanism of the self-repairing function was approached. It was revealed that the silicate additive was acting as a catalyst to promote a series of complex tribochemical reactions to form a regenerated layer with amorphous carbon structure on the worn surface under high-friction temperature and pressure in the friction and wear process.

1 January 1998 in Ceramics International
Verified
Journal Article
Closed access
XZXingzhong Zhao
Xingzhong Zhao
JLJiajun Liu
Jiajun Liu
BZBaoliang Zhu
Baoliang Zhu
JOJinlin Ouyang
Jinlin Ouyang
QXQunji Xue
Qunji Xue

25 December 2017 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
PJPeng Jin
Peng Jin
JLJiajun Liu
Jiajun Liu
Jianhua LiuJianhua Liu
Jianhua Liu
LLLankai Li
Lankai Li
JCJunsheng Cheng
Junsheng Cheng
Qiuliang WangQiuliang Wang
Qiuliang Wang
Modern yttrium barium copper oxide (YBCO) superconductor tape can carry a high critical current under a rather high magnetic field with good strain tolerance. However, the interface between the laminas is quite weak, and the interfacial strength has thus attracted considerable research interests. We designed a new method to analyze the interfacial strength of YBCO tape. A piece of tape was first embedded in a rectangular-section beam of epoxy resin, with the tape plane parallel to the middle cross section of the beam and the tape edge at the beam surface. The epoxy beam height was greater than the tape width. Three-point bending was applied to the beam, with one point on the opposite side of the tape across the beam and the other two points at the two ends. The interface was thus tensed during loading. In this way, the interfacial strength could be directly determined, and the interfacial energy could be calculated from the force–displacement curve. The crack interface was examined using scanning electron microscopy and analyzed using energy-dispersive X-ray spectroscopy. The average interface strength was 5.16 MPa. The experimental data were used to further simulate the crack behavior during the cooling process. 1

1 May 1993 in Wear
Verified
Journal Article
Closed access
MYMa Yan-Sheng
Ma Yan-Sheng
LJLiu Jia-Jun
Liu Jia-Jun
ZBZhu Bao-Liang
Zhu Bao-Liang
ZGZhai Guang-Jie
Zhai Guang-Jie
ZLZheng Lin-Qing
Zheng Lin-Qing