Pushkar Jha

Dr. Pushkar Jha


Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 July 2013 in Journal of Composite Materials
Verified
Journal Article
Closed access
PJPushkar Jha
Pushkar Jha
PGPallav Gupta
Pallav Gupta
DKDevendra Kumar
Devendra Kumar
OPOm Parkash
Om Parkash
This investigation reports the phase, microstructure and hardness of ZrO2-reinforced iron-based metal matrix composites synthesized by powder metallurgy. The process involved the preparation of homogeneous mixture of electrolytic iron powder with different weight percentages (5%, 10%, 20% and 30%) of ZrO2 by milling, compaction in the form of rod and sintering in the temperature range of 900–1100℃ for 1–3 h in argon atmosphere. The sintered samples were subjected to X-ray diffraction for phase analysis and to scanning electron microscopy for microstructure evaluation. The X-ray diffraction and scanning electron microscopy results show the presence of Fe, ZrO2 and Zr6Fe3O phases. This Zr6Fe3O phase is formed due to reactive sintering. From these studies it is concluded that two types of sintering are involved: (a) solid state sintering between Fe particles and (b) reactive sintering with the formation of iron zirconium oxide. Density and hardness of composite specimens were found to depend on fraction of ZrO2, the nature of sintering and the formation of Zr6Fe3O phases.

16 June 2017 in Friction
Verified
Journal Article
Open access
PDF file
PJPushkar Jha
Pushkar Jha
RGRakesh Kumar Gautam
Rakesh Kumar Gautam
RTRajnesh Tyagi
Rajnesh Tyagi
The present study synthesized Cu–4 wt% Ni matrix composites reinforced with different percentages of TiC (0, 2, 4, 6, and 8 wt%) through high-energy ball milling, followed by compaction and sintering. The friction and wear behavior was examined at four different normal loads of 5, 10, 15, and 20 N. A constant sliding speed of 1.25 m/s was maintained while sliding against a hardened counterface made of EN31 steel (HRC 60) under ambient conditions using a pin-on-disk test rig. The composite hardness increased until the addition of 4 wt% of TiC, beyond which it was observed to decrease. Such a trend may be attributed to the TiC agglomeration in the composites containing relatively larger amounts of TiC (i.e., 6 and 8 wt%). The wear rate linearly increased with the load. However, the composites exhibited a lower rate of wear than the matrix alloy, which may have resulted from the relatively higher hardness of composites. The observed friction and wear behavior has been explained on the basis of hardness and presence of the transfer layer on the worn surface and its nature, i.e., loose or well compacted. Addition of 4 wt% TiC showed the optimum performance in terms of friction and wear caused by its higher hardness and ability to hold a transfer layer of a relatively larger thickness compared to the other materials. The wear mechanism for the Cu4Ni matrix alloy was a mix of adhesive and oxidative wear and primarily abrasive for the composites containing hard TiC particles.

24 August 2016 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
PJPushkar Jha
Pushkar Jha
RGR. K. Gautam
R. K. Gautam
RTRajnesh Tyagi
Rajnesh Tyagi
DKDevendra Kumar
Devendra Kumar

21 March 2022 in Materials Today: Proceedings
Verified
Journal Article
Closed access
NKNeetu Kanaujia
Neetu Kanaujia
RARahul
Rahul
JBJitendra Kumar Behera
Jitendra Kumar Behera
SMSambit Kumar Mohapatra
Sambit Kumar Mohapatra
ABAsit Behera
Asit Behera
BRBharat Chandra Routara
Bharat Chandra Routara

28 June 2024 in Materials Chemistry and Physics
Verified
Journal Article
Closed access
RGRohit Kumar Singh Gautam
Rohit Kumar Singh Gautam
IMIndra Prakash Mishra
Indra Prakash Mishra
VTVivek Mani Tripathi
Vivek Mani Tripathi
SMSubhash Mishra
Subhash Mishra
ZAZubair Ahmed
Zubair Ahmed
HNHemant Nautiyal
Hemant Nautiyal

18 October 2023 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
GAGULAM MOHAMMED SAYEED AHMED
GULAM MOHAMMED SAYEED AHMED
DSDEVENDRA KUMAR SINHA
DEVENDRA KUMAR SINHA
MJMoera Gutu Jiru
Moera Gutu Jiru
JAJameel Mohammed Sardar Ali
Jameel Mohammed Sardar Ali
NAZIA HOSSAINNAZIA HOSSAIN
NAZIA HOSSAIN
GAGULAM MOHAMMED SAYEED AHMED
GULAM MOHAMMED SAYEED AHMED
Natural and synthetic fibers offer a multitude of advantages within the automotive sector, primarily due to their lightweight properties, including appealing characteristics such as adequate mechanical strength, low density, improved acoustic–thermal insulation, cost-effectiveness, and ready availability. In this study, we aimed to strengthen epoxy-based composites with natural and synthetic fibers using bamboo and glass, respectively. Additionally, the reinforcement processing of this hybrid composite material was optimized using a Taguchi L9 (nine experimental runs) orthogonal array design with linear modeling through the Design of Experiment (DoE) principles. The fibers were alkali-treated with sodium hydroxide (NaOH), and the composites were manufactured through the hand lay-up process at ambient temperature and characterized comprehensively using ASTM standard methods. The experimental results of the bamboo–glass fiber composite materials presented a significantly high tensile strength of 232.1 MPa and an optimum flexural strength of 536.33 MPa. Based on the overall Taguchi and linear modeling analysis, the NaOH treatment, fiber content, and epoxy resin concentration were optimized. These findings reveal that the ideal combination consists of 20% fiber content, 8% NaOH treatment, and 65% epoxy resin concentration. The statistical method Analysis of Variance (ANOVA) was employed to confirm the significance of these factors. The integration of the amount (%) of bamboo fiber used played a pivotal role in influencing the mechanical properties of this hybrid composite. Overall, this study demonstrates that the reinforcement of natural fiber with polymeric material composites on epoxy enhanced the composite characteristics and quality. Therefore, this bamboo–glass–epoxy-based composite can be recommended for lightweight structural applications, especially in the automotive sector, in the future.