Flax is a commercial crop grown in many parts of the world both for its seeds and for its fibers. The seed-based flax variety (linseed) is considered less for its fiber after the seed is extracted. In this study, linseed straw was utilized and processed to extract fiber and cellulose through optimization of retting time and a multi-step alkaline peroxide extraction process using the Taguchi design of experiment (DOE). Effects of retting duration on fiber properties as well as effects of solvent concentration, reaction temperature, and time on removal of non-cellulosic fiber components were studied using the gravimetric technique, Fourier transform infrared (FTIR) spectroscopy and thermal studies. Based on these findings, retting for 216 h at room temperature should offer adequate retting efficiency and fiber characteristics; 70% cellulose yield was extracted successfully from linseed straw fiber using 75% ethanol–toluene at 98 °C for 4 h, 6% NaOH at 75 °C for 30 min, and 6% H₂O₂ at 90 °C for 120 min.

Modern electronic devices need effective shielding from external Electromagnetic Interference (EMI) to function correctly. The Electromagnetic (EM) waves emerging from communication systems and medical devices must be isolated to safeguard humans from exposure. The mechanics of EMI shielding as well as several characterization methods are discussed in this paper. Existing trends and practices of designing, fabrication and use of polymer matrix composites for EMI shielding applications are covered. Several approaches and new solutions for fabricating composites either by modification of filler or matrix are discussed and prominent features of EMI shielding material are also discussed. Conducting polymers such as polyaniline, polypyrrole and polythiophene make them adept for EMI shielding applications. An assessment of the different factors affecting the performance of EMI shielding materials is also presented.

Aluminum metal matrix composites are potential materials for aerospace and automobile industrial applications due to their enhanced mechanical and tribological properties. Aluminum reinforced with silicon carbide particles has been developed with enhanced mechanical and tribological behavior, but it lacks wettability between matrix and reinforcement causing weak bonding, which reduces the degree of enhancement. The objectives of this study were to fabricate aluminum-based metal matrix composites with enhanced wettability at varying stirring speeds (350, 450, 550 rpm), stirring time (5, 10, 15 min), weight percentage of SiC (0, 5, 10 wt.%), and weight percentage of MoS₂ (0, 2, 4 wt.%). Nine samples were fabricated using stir casting based on Taguchi L9 orthogonal array. Hardness, tensile strength, and wear rate of the developed composite were investigated and analyzed as a single response characteristic using Taguchi’s signal-to-noise ratio and as a multi-response characteristic using hybrid Taguchi–grey relational analysis (HTGRA). The results revealed that the addition of SiC in the composite produced better hardness, tensile strength, and wear rate. The addition of MoS₂ in the composite showed better hardness and tensile strength only up to 2 wt.% of MoS₂, and in the case of wear rate, the addition of MoS₂ in the composite up to 4% showed better wear resistance. Al–SiC–MoS₂ hybrid composite shows better enhancement in hardness, tensile strength, and wear resistance than the Al–SiC composite.

Special attention is required when joining two materials with distinct chemical, physical and thermal properties in order to make the joint bond robust and rigid. The goal of this study was to see how significantly different tungsten inert gas (TIG) welding process parameters (welding current, gas flow rate, root gap, and filler materials) affect mechanical properties (tensile, hardness, and flexural strength), as well as the bead width and microstructural properties, of dissimilar welds In comparison to SS 316 and AISI 1020 low-carbon steel. TIG welding parameters were optimized in this study using a Taguchi-based desirability function analysis (DFA). From the experimental results, it was observed that welded samples employing ER-309L filler wires had a microstructure consisting of a delta ferrite network in an austenite matrix. The tensile strength experimental results revealed that welding current, followed by GFR, was a highly influential parameter on tensile strength. Weld metals had higher hardness and flexural strength than stainless steel and carbon steel base metals. This was supported by the fact that the results of our tests had hardness ratings greater than a base for the FZ and HAZ, and that no crack was observed in the weld metal following U-shape flexural bending. Welding current has a significant impact on the bead width of welded specimens, followed by root gap. Furthermore, the dissimilar welded sample responses were optimized with a composite desirability percentage improvement of 22.90% by using a parametric setting of (A2B4C4D2). Finally, the validation of the experiment was validated by our confirmation test results, which agreed with the predictive optimum parameter settings.

Friction stir consolidation (FSC) is a promising manufacturing process for metal matrix hybrid composites (MMHC) with excellent mechanical properties. The originality of this study involves the exploration of the fabrication technique (FSC), the selection of materials and the optimization of wear behavior via a systematic investigation of the process parameters. The aim of this study was to optimize and investigate the wear behavior of MMHCs fabricated using FSC. The optimum sample was nominated for thermogravimetric analysis (TGA) and wear morphology analysis using SEM imaging. Material compositions of 7.5%wt of SiC, 7.5%wt of ZrO2 and 85%wt of AZ61 were considered for the experimental investigation. The RSM Box–Behnken design followed by a genetic algorithm (GA) was implemented to optimize the process parameters of sliding distance, speed and load at 350 m, 500 m and 650 m; 220 rpm, 240 rpm and 260 rpm; and 20 N, 30 N and 40 N, respectively. The RSM Box–Behnken result showed that the minimum wear rate of 0.008 mg/m was obtained at 350 m, 20 N and 240 rpm, whereas GA predicted the optimum parametric setup at 350 m, 20 N and 220 rpm. Additionally, TGA showed the material’s thermal stability from 375 °C to 480 °C. Generally, MMHCs exhibited a promising wear performance, proving the effectiveness of the FSC.

In recent years, partial replacement of cement with bagasse ash has been given attention for construction application due to its pozzolanic characteristics. Sugarcane bagasse ash and fine bagasse particles are abundant byproducts of the sugar industries and are disposed of in landfills. Our study presents the effect of burning bagasse at different temperatures (300 °C and 600 °C) on the compressive strength and physical properties of bagasse ash-blended mortars. Experimental results have revealed that bagasse produced more amorphous silica with very low carbon contents when it was burned at 600 °C/2 h. The compressive strength of mortar was improved when 5% bagasse ash replaced ordinary portland cement (OPC) at early curing ages. The addition of 10% bagasse ash cement also increased the compressive strength of mortars at 14 and 28 days of curing. However, none of the bagasse ash-blended portland pozzolana cement (PPC) mortars have shown improvement on compressive strength with the addition of bagasse ash. Characterization of bagasse ash was done using XRD, DTA-TGA, SEM, and atomic absorption spectrometry. Moreover, durability of mortars was checked by measuring water absorption and apparent porosity for bagasse ash-blended mortars.