The organic compound caffeine when detected in environmental matrices such as surface waters and groundwater is considered as an emerging contaminant, in which its effects are still unknown. Therefore, in the present research, zinc oxide-based catalysts impregnated with iron and silver were prepared for the reaction of caffeine degradation by heterogeneous photocatalysis. The wet impregnation method with excess solvent was applied to the preparation of the materials, later they were characterized by adsorption of N2, X-ray diffraction and photoacoustic spectroscopy. Then, the photodegradation, photolysis and adsorption tests were carried out, in which it was observed that only the presence of the radiation or photocatalysts could not sufficiently degrade the caffeine, however when combined radiation with all the catalysts studied here presented degradation above 70% at the end of 300 minutes of the reaction, and the best catalyst studied was that containing 8% Ag in non-calcined ZnO. Thus, these results point out that the methodology employed in this research, both for the preparation of the catalysts and in the process of the photocatalysis reaction, was efficient in the degradation of the emerging contaminant, caffeine, which could later be used for a mixture of other contaminants.
The circular economy seeks to better use materials and minimize waste generation. This article evaluated the use of granite rock powder, a mining residue, as an adsorbent for the Basazol Yellow 5G (BY5G) dye and the reuse of the residue generated by the by treating this effluent in construction products. Characterization of the adsorbent material by N2 physisorption indicated a surface area of 1514 m2 g−1. Energy-dispersive spectrometry (EDS) and X-ray diffraction (XRD) confirmed the presence of silica in the sample and the absence of amorphous halos. The kinetic study showed a removal of approximately 98% at 298 K, and the pseudo-second-order model obtained the best fit. The adsorption isotherm satisfied the Langmuir model and was consistent with the L-type isotherm. The negative value of the Gibbs energy (ΔG°) and the positive value of the enthalpy (ΔH°) indicate that the process is spontaneous and endothermic. The activation energy (Ea) indicates the occurrence of chemical adsorption. The desorption rate was low for the adsorbate, demonstrating the possibility of using residual adsorbent material as a filler in mortar and concrete. The material did not exhibit pozzolanic characteristics and, even after adsorption, it showed favorable results when replacing 10% of the cement with GRP viable for use in civil construction even after the adsorption process.
This study describes the application of new and low cost biosorbent, shells of urucum (Bixa Orellana), for removal of lead ions (Pb(II)) from water solution. The urucum shells were characterized by Fourier transform infrared spectroscopy and scanning electron microscopy techniques. Batch adsorption experiments were performed in order to evaluate the effect of pH, agitation speed, adsorbent dosage, contact time, temperature, presence of interfering ions and matrix effect on the adsorption of process. The kinetics of biosorption followed pseudo-second-order model. Langmuir and Freundlich isotherm models were applied to describe the biosorption of Pb(II) by urucum shells. The Langmuir model showed better fit and the estimated biosorption capacity was 43.6 mg g-1. The negative Gibbs free energy, ΔG°, confirms the spontaneous nature and positive value of enthalpy, ΔH°, the endothermic character of the process. Furthermore, we also performed an evaluation of matrix and others ions effect on the biosorption process
This study aimed to investigate the technical feasibility of replacing cement in mortar production with sludge generated in wastewater treatment plants (WWTPs), prepared using different treatments. The sludge used in the experiments was processed using four different methods to investigate the effect of processing on the mechanical strength of the specimens. The sludge was then mixed with mortar in different proportions, and samples were produced for flexural and compressive strength tests. The results showed that specimens with 7% sludge from the burned treatment exhibited the highest resistance, surpassing the standard. Specimens with sludge from the drying treatments showed similar results. This study found that using sludge in mortar production could lead to energy savings compared to traditional cement production methods. Moreover, the incorporation of sludge resulted in mortars that met the specifications of the EN 998-1:2018 standard, thereby indicating their technical feasibility. Therefore, this study demonstrated the potential of using sludge from WWTPs as a substitute for cement in mortar production, which could contribute to the reduction in the environmental impacts caused by civil construction and the development of sustainable alternatives for the disposal of sludge generated in WWTPs.
The sludge from water treatment plants (WTP) is a waste from the water process. This study evaluated the effect of incorporating water treatment plant (WTP) sludge, replacing the water used in compacted soil–cement mixtures. The materials were characterized by Scanning Electron Microscopy (SEM) associated with Energy Dispersive Spectroscopy (EDS) and Atomic Absorption Spectrometry (AAS). The soil, with the addition of liquid WTP sludge, presented an apparent dry specific weight (ƴd) of 1.77 gf·cm−3, the optimum moisture value in the compaction test of 15%, and the cement contents tested were 7, 11, and 14%. The specimens were molded using a WTP sludge–cement–soil mixture under the conditions mentioned above, and the simple compression results showed values within the range of 2.5 to 9.3 MPa, as specified by the Brazilian Technical Standard (NBR) 8491/2012. The hydraulic conductivity performed on the test specimen after 28 days of curing resulted in a coefficient (k) of 7.49 × 10−9 cm·s−1, classified as little permeable. The result obtained from aluminum leaching was 0.12 mg·L−1, within the maximum limit allowed by NBR 10004/2004. Therefore, liquid WTP sludge has a significant capacity for incorporation into the compacted soil–cement mixture and the potential to manufacture ecological bricks, an alternative environmentally sustainable brick.