A novel high conversion ratio bidirectional C-dual transformers-LC (CDT-LC) resonant DC-DC converter is proposed in this paper. Based on the traditional LLC, an auxiliary transformer and an extra resonant capacitance are employed in CDT-LC structure. It not only harvests high efficiency but exhibits a good voltage gain feature. Especially for the case of light load, CDT-LC still harvests a high efficiency, compared with traditional converters. Also, it can achieves a fast gain reduction when the switching frequency is higher than resonant frequency. In this paper, the operating principles of the converter are analyzed in both bi-directional operation modes. In additional, its dual-transformers structure feature and voltage gain characteristics are discussed in details. Furthermore, the parameter design method is provided. Moreover, the loss breakdown for the converter is given in details. At last, a 2.5kW prototype is established to verify the performance of the CDT-LC converter, and its maximum efficiency reaches 97%.
A two‐mode resonant DC–DC converter with auxiliary switch (named as sLLC‐C) has been presented. Two simple structural circuits (namely LLC and LLCC) are integrated into one topology with only two magnetic cores, through the topological transformation method. The proposed converter successfully inherits the advantages of the above two circuits, while avoiding their drawbacks as well. At the rating condition, it functions as an LLC circuit, and thus high conversion efficiency is easily obtained. The LLCC working mode is called automatically once the input voltage increases. In such a way, within a limited frequency range, the voltage gain range is effectively extended. A detailed parameter design is given to help achieve desirable performances. Finally, experiments are carried out to validate the feasibility and correctness of the proposed sLLC‐C converter. The output voltage is maintained at 400 V, even if the input voltage varies in the range of 150–400 V. Besides, the preferable soft‐switching characteristics are ensured for both the power switches and secondary‐side diodes. The maximum efficiency of 97.3% is achieved. Thus, wide voltage gain range and high conversion efficiency are acquired simultaneously. These performances make the proposed converter well appropriate for the fuel cell generation applications.
A high frequency dual-buck full-bridge inverter for small power renewable energy application is proposed in this paper. A switching frequency of 400 kHz is achieved with the adoption of the SiC power device. A two-pole two-zero (2P2Z) compensator is employed in the outer voltage loop to generate the current reference for inner current loop. A 3P3Z compensator is adopted in the inner current loop to track the current reference. A systematic way for calculating the losses of high frequency inverter is presented, and the losses of the components are thoroughly analyzed. The turn-on and turn-off procedures of the inverter are discussed in detail. The losses caused by high frequency are calculated accurately, and the loss distribution is established as well. The procedure of the loss analysis gives a practical example for calculating the loss of similar type inverters. Moreover, deviation between pulse width modulation (PWM) control signal and switching response in high frequency switching is thoroughly analyzed. The influence of deviation is verified by designed experiment. Hence, a compensation method is proposed in order to minimize the influence. The compensation effect is validated by experiment and simulation. Finally, a 1-kW prototype is built to verify the feasibility of the theoretical analyses. The grid-connected maximum output power experiment is completed at 1 kW with the efficiency of 96.1% and the total harmonic distortion (THD) of 1.8%. The comparison experiments of power loss between Si and SiC power devices are carried out. The experiment results confirm the loss calculation method to be valid.
This paper proposes and discusses a novel AC/DC converter suitable for small-scaled wind power generation system applications. By introducing flyback cells into the three-phase single-switch Boost circuit, the proposed converter is designed as single-stage and has both rectification and high step-up power conversion functions. It is able to obtain high voltage gain at low input voltage level, and high efficiency, low total harmonic distortion (THD) at rated power. The inherent power factor correction (PFC) is also determined, and can reach 0.99. Besides, since no electrolytic capacitor is employed and high voltage gain is achieved, the converter can also collect weak power at low input voltage in combination with energy storage devices, and contribute to a better low-wind-speed/low-power performance. Finally, a 400 W prototype is built to verify the theoretical analysis, and its efficiency is 87.6%, while THD is 7.4% at rated power.
A high frequency dual-buck full-bridge inverter for small power renewable energy applications is proposed in this paper. The implementation of the wide band gap SiC (Silicon Carbide) power device contributes to the high switching frequency of 400 kHz. This high frequency contributes to reduced converter volume as well as improved power density, which greatly strengthens its portability and application range. For the control strategy, a voltage-current dual loop controller is employed. A three-pole-three-zero (3P3Z) compensator is applied in the current loop in order to track the current reference without static error. A voltage loop two-pole two-zero (2P2Z) compensator is used to generate the current reference for stabilizing the DC bus voltage. Not only is the inner current loop analyzed in detail, which includes the modeling of the equivalent inductor-capacitor-inductor (LCL)-type inverter and the design of the 3P3Z compensator, but also the outer voltage loop is discussed, the model of which is established based on the energy balance. Furthermore, a feedback linearization method is adopted to simplify the duty cycle calculation and helps to accelerate the control speed. A second-order generalized integrator software phase lock loop (SOGI-SPLL) is employed to obtain the phase angle and to synchronize the inverter output current with the grid voltage. A parallel structure algorithm is conducted based on a dual-core microcontroller unit (MCU) for the first time to control the high frequency inverter. This approach avoids the contradiction between the high frequency operation and the limited computing capacity of the conventional single-core MCUs. The software structure, time-consuming distribution, and interactive communication method are analyzed in detailed. Finally, this paper verifies the feasibility of the theoretical analyses through simulation and experiments based on a 1 kW prototype.
In this paper, two multi-element resonant DC-DC converters are analyzed in detail. Since their resonant tanks have multiple resonant components, the converters display different resonant characteristics within different operating frequency ranges. Through appropriate design, both of the two proposed converters successfully lower the conversion losses and, meanwhile, broaden the voltage gain ranges as well: one converter is able to take full usage of the third order harmonic to deliver the active power, and thus the effective utilization rate of the resonant current is elevated; while the another minimizes the entire switching losses for power switching devices by restricting the input impedance angle of the resonant tank. Besides, the loss distribution is analyzed for the purpose of guiding the component design. In the end, two 500 W prototypes are fabricated to test the theoretical analyses. The results demonstrate that the two proposed converters can achieve wide voltage gain with the small frequency deviation, which noticeably contributes to highly efficient conversion. Their peak efficiencies are measured as 95.4% and 95.3%, respectively.