Qiang Song

Dr. Qiang Song


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 February 2024 in Materials
Verified
Journal Article
Open access
PDF file
FPFeifei Peng
Feifei Peng
CCChang Chen
Chang Chen
SJShaowu Jiu
Shaowu Jiu
QSQiang Song
Qiang Song
YCYanxin Chen
Yanxin Chen
The production of autoclaved aerated concrete via the autoclaving process incurs substantial energy consumption, posing a challenge to sustainable economic development. Herein, a novel nonautoclaved aerated concrete (NAAC) was prepared using sulfoaluminate cement as the primary raw material and aluminum powder as the aerating agent. The physicomechanical characteristics and pore structures of the sulfoaluminate-cement-based (SAC) NAAC (SAC-NAAC) were examined through X-ray diffraction, thermogravimetry, and scanning electron microscopy. The findings revealed that the optimal mechanical attributes of the SAC-NAAC were achieved at a water–cement ratio of 0.55, with a specific content ratio of polycarboxylate superplasticizer–borax–calcium stearate–sodium hydroxide at 0.24%:0.32%:0.36%:2.90%, along with 0.40% aluminum powder. The SAC-NAAC samples, with a bulk density range of 600–750 g/m3, exhibited a compressive strength of 3.55–4.16 MPa, porosity of 45.9–63.5%, and water absorption rate of 60.2–74.4%. The weight loss in the SAC-NAAC with different aluminum powder contents ranged between 15.23% and 16.83%. The prismatic ettringite (AFt) crystals served as the main source of strength for the SAC-NAAC, and AH3 was attached to the AFt surfaces in a microcrystalline gel phase, thereby further enhancing the strength of the SAC-NAAC. Thus, the lightweight, high-strength SAC-NAAC has great potential as a nonautoclaved aerated concrete.

23 April 2024 in Buildings
Verified
Journal Article
Open access
PDF file
QSQiang Song
Qiang Song
QHQian He
Qian He
JNJiao Nie
Jiao Nie
TSTiantian Song
Tiantian Song
HZHong Zhou
Hong Zhou
FCFuan Cheng
Fuan Cheng
In order to explore a wider range and lower cost of raw materials for the preparation of magnesium silicate hydrate (M-S-H), an acid-leaching method was employed to extract and separate high-purity magnesium hydroxide (Mg(OH)2) with a purity higher than 97% and amorphous silica with a purity higher than 90% from four types of natural silicate minerals (serpentine, peridotite, zeolite, and montmorillonite). These two intermediate products, which are amorphous silica and magnesium hydroxide, were used to prepare M-S-H, and the influence of curing at two temperatures, 50 °C and 80 °C, on the properties of M-S-H was investigated. The results showed that with the increase in curing temperature, the bound water content, tetrahedral polymerization degree, and Mg(OH)2 content increased. There was a good correlation between the increase in strength and the bound water content of M-S-H. This work provides a possible technological route for expanding the raw materials for preparing magnesium silicate hydrate cementitious materials and utilizing the abundant magnesium silicate minerals in the Earth’s crust.

12 September 2025 in Buildings
Verified
Journal Article
Open access
PDF file
XGXu Gao
Xu Gao
XZXiaomin Zhang
Xiaomin Zhang
CCChang Chen
Chang Chen
XLXuan Liu
Xuan Liu
JZJiaqi Zhu
Jiaqi Zhu
YCYanxin Chen
Yanxin Chen
Rock wool trim waste (RWTW) presents considerable recycling difficulties due to the release of toxic volatiles from phenolic resin binders during pyrolysis, which also hinders its effective utilization in rock wool-based alkali-activated cementitious composites (RWACCs). Traditional thermal and chemical resin removal approaches are energy-consuming, produce secondary pollutants, and can diminish the aluminosilicate reactivity of RWTW. This study introduces an innovative mechanochemical ball milling pretreatment aimed at selectively breaking resin C−O bonds while maintaining the integrity of the mineral phase, thus facilitating eco-friendly and efficient RWTW recycling. By applying different milling durations (30–120 min), the properties of RWTW particles were systematically characterized through granulometry, XRD, SEM, and FT-IR. The hydration kinetics, compressive strength, and microstructure of RWACC pastes were thoroughly examined. Key findings confirm that 120 min is the optimum ball milling duration, as validated by weighted sum analysis. This duration yielded a median particle size (D50) of 7.15 μm, significantly increased reactivity (evidenced by a 28-day activity index of 85.3%), and outstanding mechanical properties, achieving flexural and compressive strengths of 15.73 MPa and 97.27 MPa, respectively. The mechanochemical process successfully encapsulated organic residues within the geopolymer matrix, preventing toxic emissions. This synergistic approach between resin degradation and enhanced reactivity demonstrates a viable route for the industrial-scale valorization of RWTW. It significantly contributes to the circular economy objectives in the construction sector.