Tribological testing of moving shaft/sealing pairs in complex environments is at the frontline of research. Machines working in abrasive conditions are subject to different wear effects. It is not only valid on Earth but especially valid for rovers and future robots used in Mars and Moon missions. The aim of our joint research with the European Space Agency is to study the abrasion phenomena of moving machine elements on Mars and the Moon by using artificial soil samples (“simulants”). This review details mainly the available simulant sources and recommend a selection of the most suitable ones for tribological testing. Moreover, the potential mating structural materials subjected to abrasive space applications are reviewed briefly. The tribological tests are exploring the features of the rotary shaft/seal relationship that is subject to dry friction and intense abrasion. By using the simulants, measurements are performed under laboratory conditions with both a sample test and a real shaft/seal connection. Parameters of the selection criteria were defined, and classification of the simulant sources were made. It was found that simulant particle size distribution and chemical substance content are detailed enough only for a limited type of available artificial Moon and Mars soil samples. Four simulants were identified and applied later in the tribological testing. For the shaft materials, based on a detailed case study of polymers, steel, and aluminum alloys, a high-strength aluminum alloy with a hard anodized surface and a stainless steel were selected for further abrasion tests.
For space missions to either the Moon or Mars, protecting mechanical moving parts from the abrasive effects of prevailing surface dust is crucial. This paper compares the abrasive effects of two lunar and two Martian simulant regoliths using special pin-on-disc tests on a stainless steel/polytetrafluoroethylene (PTFE) sealing material pair. Due to the regolith particles entering the contact zone, a three-body abrasion mechanism took place. We found that friction coefficients stabilised between 0.2 and 0.4 for all simulants. Wear curves, surface roughness measurements, and microscopic images all suggest a significantly lower abrasion effect of the Martian regoliths than that of the lunar ones. It applies not only to steel surfaces but also to the PTFE pins. The dominant abrasive micro-mechanism of the disc surface is micro-ploughing in the case of all tests, while the transformation of the counterface is mixed. The surface of pin material is plastically transformed through micro-ploughing, while the material is removed through micro-cutting due to the slide over hard soil particles.
Tribological testing of moving shaft/sealing pairs in complex environments is at the frontline of research. Machines working in abrasive conditions are subject to different wear effects. It is valid not only on the Earth but especially valid for rovers and future robots used in Mars and Moon missions. The aim of our joint research with the European Space Agency is to study the abrasion phenomena of moving machine elements on Mars and the Moon, by using artificial soil samples (“simulants”). This review detail the available simulant sources and recommend a selection of the most suitable ones for tribological testing. Moreover, the potential mating structural materials subjected to abrasive space applications are reviewed. The tribological tests are exploring the features of the rotary shaft/seal relationship that is subject to dry friction and intense abrasion. By using the simulants, measurements are performed under laboratory conditions with both a sample test and a real shaft/seal connection. Parameters of the selection criteria have been defined and classification of the simulant sources were made. It was found that simulant particle size distribution and chemical substance content is detailed enough only for a limited type of available artificial Moon and Mars soil samples. 4 simulants have been identified and applied later in the tribological testing. For the shaft materials, based on a detailed case study of polymers, steel and aluminium alloys, a high-strength aluminium alloy with a hard anodized surface and a stainless steel were selected for further abrasion tests.
In this paper, the abrasive effects of lunar simulant regoliths (LHS-1, LMS-1) have been investigated. Sealing performance of different sealant pin materials on stainless steel has been tested by the pin-on-disc method. Pin materials included block types such as pure polytetrafluoroethylene (PTFE), composite PTFE, as well as braided PTFE and hybrid-composite braided PTFE. Tribological properties were evaluated based on measured friction, wear, surface roughness and scanning electron micrographs. Most significant differences were observed in the sealing effect of the pins between the braided and the block-type pin materials. The stainless steel/pin pairs showed significantly higher (0.4–0.5) friction coefficients for the braided pins than the block ones (0.2–0.3), while there was not a significant difference in the abrasive effect of the different lunar regoliths. Although significant wear of the steel part occurred only with the block-type pins, this disadvantage was apparent in comparison with the braided pins. The abrasive particles caused deformation and eventually complete disintegration of the braided pins. Both the coefficient of friction and the wear could be estimated by a multiple linear regression model, in which different regolith size was the dominant independent parameter for the various pins.
We have investigated the sealing performance of different sealants and the abrasive effect of some Martian regolith simulants (MGS-1 and JEZ-1) by pin-on-disc tests using steel and various pin material pairs. Pin materials, representing sealants, were present in the following two forms: block types, such as pure polytetrafluoroethylene (PTFE) and composite PTFE, as well as braided pins, including pure and hybrid composite PTFE. Friction resistance, wear, surface roughness, and electron microscopy analyses were used to evaluate the tribological properties. We found significant differences between the block-type and braided pin materials regarding the sealing and wear performance. The braided pins either reached stabilized coefficients of friction at a much higher level (0.55) than the block-type pins or did not stabilize at all during the longest test duration. Martian regoliths resulted in negligible wear regarding the disc, but the hybrid composite braided pins were severely worn, causing the abrasion test to be stopped before schedule.
10 August 2026 in Progress in Agricultural Engineering Sciences
Lunar regolith is a potential substrate for plant cultivation in future bioregenerative life-support systems; however, its distinct physicochemical properties pose challenges for plant growth. In this study, white mustard was grown in mare (LMS) and highland-type (LHS) regolith simulants, each separated into fine and coarse particle-size fractions, with perlite as a control. Germination was successful across all treatments. Biomass production and reproductive performance were generally lower in regolith simulants compared with the control. Plants grown in LMS produced slightly lighter seeds than those grown in LHS, with statistically significant differences observed in the LMS coarse fraction. These results likely reflect differences in simulant chemistry, as LMS contains higher concentrations of Fe, Mg, and trace elements that may influence plant physiological responses. Particle-size distribution also affected substrate behavior, with fine fractions showing higher water retention and coarse fractions improving aeration but reducing moisture availability. These results clarify that both substrate chemistry and particle size critically affect plant productivity in lunar regolith-based agriculture.