Microbial fuel cell (MFC) technology holds significant promise for the production of clean energy and treatment of pollutants. Nevertheless, challenges such as low power generation efficiency and the high cost of electrode materials have impeded its widespread adoption. The porous microstructure of biochar and the exceptional photocatalytic properties of rutile endow it with promising catalytic potential. In this investigation, we synthesized a novel Rutile–Biochar (Rut-Bio) composite material using biochar as a carrier and natural rutile, and explored its effectiveness as a cathode catalyst to enhance the power generation efficiency of MFCs, as well as its application in remediating heavy metal pollution. Furthermore, the impact of visible light conditions on its performance enhancement was explored. The X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) analysis validated the successful fabrication of rutile composites loaded with biochar. The maximum current density and power density achieved by the MFCs were 153.9 mA/m2 and 10.44 mW/m2, respectively, representing a substantial increase of 113.5% and 225% compared to the control group. In addition, biochar-supported rutile MFCs showed excellent degradation performance of heavy metal pollutants under light conditions. Within 7 h, the Cr6+ degradation rate reached 95%. In contrast to the blank control group, the removal efficiency of pollutants exhibited increases of 630.8%. The cyclic degradation experiments also showcased the remarkable stability of the system over multiple cycles. This study successfully integrated natural rutile and biochar to fabricate highly efficient cathode photocatalyst composites, which not only enhanced the power generation performance of MFCs but also presented an environmentally sustainable and economically viable method for addressing heavy metal pollution.
The issue of heavy metal pollution has gradually emerged as a significant global concern. Microbial fuel cells (MFCs) hold immense potential for clean energy production and pollutant treatment. However, their limited power generation efficiency hampers the large-scale implementation of MFCs. The porous microstructure of biochar and the excellent physical and chemical properties of rutile render both materials promising catalysts with positive potential. In this study, we employed biochar as a carrier for rutile to fabricate a novel rutile–biochar (Rut-B) composite material, investigating its efficacy in enhancing MFC power generation efficiency as a cathode catalyst, as well as its application in heavy metal pollutant degradation. Scanning electron microscopy (SEM) results confirmed the successful preparation of biochar-loaded rutile composites. The MFC achieved maximum current density and power density values of 152.26 mA/m2 and 9.88 mW/m2, respectively—an increase of 102.7% and 224% compared to the control group without the addition of Rut-B. Furthermore, the biochar-loaded rutile MFC exhibited excellent performance in degrading heavy metal pollutants; within 7 h, the Pb2+ degradation rate reached 92.4%, while the Zn2+ degradation rate reached 84%. These rates were significantly higher than those observed in the control group, by factors of 437.2% and 345%, respectively. The cyclic degradation experiments also demonstrated the outstanding stability of the system over multiple cycles. In summary, this study successfully combined natural rutile with biochar to create an efficient electrode catalyst that not only enhances electricity generation performance but also provides an environmentally friendly and cost-effective approach for remediating heavy metal pollution.
The global serious pollution situation urgently needs green, efficient, and sustainable development methods to achieve heavy metal pollution control. The photocatalytic properties of anatase are sufficient to achieve pollution control by providing photoelectrons to harmful heavy metals. However, since natural anatase particles tend to agglomerate and deactivate in water, most studies have been conducted to prepare TiO2–biochar nanocomposites using chemical synthesis methods. In the present study, we utilized pyrolytic sintering to load natural anatase onto biochar to obtain natural anatase–biochar (TBC) composites. Characterization tests, such as X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS), showed that anatase was uniformly partitioned into the surface and pores of biochar without destroying the lattice structure. Due to its photocatalytic properties, TBC degraded Cr (VI) by 99.63% under light conditions. This is 1.58 times higher than the dark condition. Zeta potential showed that the surface of the TBC was positively charged under acidic conditions. The charge attraction between TBC and chromium salt was involved in the efficient degradation of Cr (VI). Different sacrificial agents as well as gas purge experiments demonstrated that photoelectrons (e−) and superoxide radicals () dominated the degradation of Cr (VI). TBC has the characteristics of high efficiency, stability, and sustainability. This may provide a new idea for the preparation of photocatalytic materials and the realization of environmental protection and sustainable development through heavy metal pollution control.
Microbially induced calcium carbonate precipitation (MICP) is a promising biotechnology for environmental remediation; however, the high cost of conventional chemical-grade calcium sources limits its large-scale scalability. This study evaluated the feasibility of utilizing an aqueous extract of natural attapulgite clay as a sustainable, low-cost calcium source for MICP-mediated arsenic (As) immobilization in both aqueous and soil systems. Among the tested minerals, Baiyin attapulgite (group B) exhibited the highest calcium content (62,808.94 mg kg−1) and minimal toxic metal impurities, providing a favorable chemical matrix for biomineralization. At an optimal solid-to-liquid ratio of 1:10, Lysinibacillus fusiformis LF and Enterococcus LZU-1 successfully induced calcite precipitation driven by the attapulgite extract. In batch aqueous remediation experiments (20 days), the attapulgite extract significantly enhanced As removal efficiency compared to the controls; As removal rates peaked at 66.4% for strain LZU-1 (with LZ1 extract) and 65.8% for strain LF (with group B extract), drastically outperforming the standard CaCl2 groups (31.2–37.3%) and blank controls (21.8–24.5%). Concurrently, soil incubation experiments (30 days) demonstrated that the combined application of attapulgite and MICP bacteria reduced the highly bioavailable exchangeable As fraction from 0.115 to approximately 0.03 mg kg−1, while effectively driving its transformation into more stable carbonate-bound and organic-bound fractions without causing secondary soil salinization. Morphological and mechanistic analyses revealed that, compared to the well-defined euhedral crystals in the CaCl2 control, the precipitates mediated by the clay extract exhibited distinctly irregular, defect-rich rhombohedral structures. This structural disruption was governed by the natural matrix effect of attapulgite, which simultaneously supplied dissolved Ca2+ and provided an abundance of fine clay fragments, calcite micro-grains, and associated amorphous Fe/Al/Mn-bearing phases. These constituents acted as physical scaffolding and heterogeneous nucleation sites that became embedded in the growing CaCO3 lattice, driving the formation of highly reactive, defect-rich clay-calcite-arsenic composite precipitates that efficiently encapsulated arsenate. Mantel analysis further revealed that the remediation efficiency was significantly correlated with key environmental variables including Ni, V, Ca. These findings highlight the dual-system potential of natural attapulgite as an inexpensive, eco-friendly calcium alternative for sustainable MICP-based remediation of As-contaminated water and agricultural soils.