While various approaches have been developed to minimize rebar cutting waste, such as optimizing cutting patterns and the lap splice position, reducing rebar usage by minimizing the number of splices remains uninvestigated. In response to these issues, a two-stage optimization algorithm was developed that prioritizes the use of special-length rebar to achieve a near-zero rebar cutting waste (N0RCW) of less than 1%, while also reducing overall rebar usage. The two-stage algorithm first optimizes the lap splice position for continuous rebar considering the use of a special-length rebar, which reduces the number of splices required. It then integrates a special-length minimization algorithm to combine the additional rebar. The algorithm was applied to beam structures in a small-sized factory building project, and it resulted in a notable reduction of 29.624 tons of rebar, equivalent to 12.31% of the total purchased quantity. Greenhouse gas emissions were reduced by 102.68 tons, and associated costs decreased by USD 30,256. A rebar cutting waste of 0.93%, which is near zero, was achieved. These findings highlight the significant potential of the proposed algorithm for reducing rebar waste and facilitating sustainable construction practices. The algorithm is also applicable to other reinforced concrete projects, where the associated advantages will be amplified accordingly.
The extensive utilization of rebar during the construction of the project generates immense rebar waste, leading to increased construction costs and significant greenhouse gas emissions. Various approaches have been explored focusing on the minimization of rebar-cutting waste, such as optimizing cutting patterns, lap splice position, and special-length rebar utilization. Nonetheless, reducing rebar usage by minimizing the number of splices remains uninvestigated. In response to these issues, a two-stage optimization algorithm was developed, prioritizing special-length rebar to achieve near-zero rebar-cutting waste of less than 1% and concurrently reduce rebar usage, thereby promoting sustainable construction practices. The two-stage algorithm presented in this study involves the optimization of the lap splice position for the continuous rebar with a reduction of splices number. Furthermore, it integrates a special-length minimization algorithm for the additional rebars. Applying the algorithm to beam structures in a small-sized factory building project led to a notable reduction of 29.624 tons of rebar, equivalent to 12.31% of the total purchased quantity. Greenhouse gas emissions were reduced by 102.68 tons, and associated costs decreased by USD 30,256. A rebar-cutting waste of 0.99% which is near zero was achieved. These findings highlight the significant potential of the proposed algorithm in reducing rebar waste and facilitating sustainable construction practices. In addition, the application of the proposed algorithm in reinforced concrete construction projects will amplify the associated advantages accordingly.
The construction industry generates significant CO2 emissions and reinforcing bars (rebar), which are a major contributor to this environmental impact. Extensive research has been conducted to address this particular issue. Recent research advances have introduced algorithms to reduce rebar waste and consumption, demonstrating the feasibility of achieving near-zero rebar cutting waste (N0RCW) through the consideration of special-length rebars. However, conventional lap splices, the most common rebar joint method, continue to consistently consume excessive quantities of rebar, despite extending beyond their mandated zones. Conversely, couplers can eliminate rebar lengths required for lapping splices, reducing the usage of rebar. Applying special-length rebars and couplers in heavily loaded structures like diaphragm walls can also significantly reduce rebar usage and cutting waste, consequently reducing CO2 emissions and the environmental and economic impacts. This research aims to optimize rebar consumption and sustainability in diaphragm wall structures by integrating mechanical couplers with a special-length rebar approach. A case study confirmed a substantial reduction in purchased rebar usage (17.95% and 5.38%), carbon emissions (15.24% and 2.25%), water footprint (17.95% and 5.38%), and environmental impact (95.18% and 30.27%) compared to the original design and recent diaphragm wall study, respectively. The broad implementation of the proposed method across various buildings and infrastructure projects could further multiply these benefits, enabling the achievement of the sustainable development goals (SDGs) adopted by the United Nations to foster sustainable construction.
Rebar usage and cutting waste contribute significantly to global greenhouse gas emissions, mainly CO2 and CH4. Researchers have explored various means to minimize cutting waste; however, these studies have yet to address reducing splices and utilizing a single specific special-length rebar. Hence, this study proposed an algorithm to minimize rebar usage and reduce rebar-cutting waste to less than 1% (near-zero rebar-cutting waste). The algorithm involves two main steps: (1) reducing the number of splices by utilizing special-length rebar and (2) adjusting the rebar accordingly based on the obtained special-length rebar. The algorithm was applied to the column rebars of an RC building to validate its effectiveness. The results confirmed a reduction in rebar usage by 3.226 tons (17.76%), a cutting waste rate of 0.83% (near-zero rebar-cutting waste achieved), a reduction of 11.18 tons in CO2 emissions, and a cost reduction of USD 3741. Employing the proposed algorithm in RC building and structure projects will amplify the corresponding benefits and contribute to the achievement of SDGs adopted by the United Nations to ensure sustainable resource usage and the acceleration of sustainable and green construction practices.
Rebar quantity estimation is pivotal for determining the cost of construction projects and is essential for bidding purposes. A bar bending schedule plays a crucial role by providing rebar information and bending instructions, facilitating efficient procurement. Traditional methods, which rely on manually extracting data from 2D (two-dimensional) drawings, are error-prone and hinder construction productivity. This study utilized a special length approach to yield optimal rebar consumption, resulting in a total rebar order of 19,582.427 t and minimizing rebar waste to 0.77%. Additionally, this method saved 3000.22 t of rebar compared to traditional methods, using only stock lengths. To enhance the accuracy and efficiency, a 3D (three-dimensional) model was developed in a Building Information Modeling (BIM) environment to prepare a Bar Bending Schedule (BBS) automatically, integrated with an Application Programming Interface (API) for data entry to eliminate manual errors. The efficacy of the proposed algorithm was confirmed by comparing the rebar quantities it generated with those obtained from optimization calculations. The results demonstrated a mean absolute error of 0.017 and a mean absolute percentage error of 1.13%, validating the algorithm’s precision. Furthermore, this method reduced the manpower required for BBS preparation by 33.33%, highlighting its potential to revolutionize construction workflow efficiency and accuracy.
The construction of reinforced concrete (RC) structures inevitably consumes an excessive number of rebars, leading to significant cutting waste and carbon emissions. Extensive research has been conducted to minimize this issue and its consequences; however, these methods consistently consume a substantial number of rebars. This includes a previous study that utilizes the lap splice position optimization and special-length rebar concept without considering the lapping zone regulation. Moreover, conventional lap splices pose inherent drawbacks that could jeopardize the structural integrity of RC members. In contrast, mechanical couplers eliminate the need for rebar lapping, effectively reducing rebar consumption. This research aims to evaluate the impact of an integrated mechanical coupler and special-length-priority minimization algorithm on the reduction in rebar consumption and cutting waste in RC columns, achieving near-zero cutting waste. To validate the effectiveness of the proposed algorithm, it was applied to the column rebars of an RC building. The results revealed a significant reduction in the ordered rebar consumption by 18.25%, accompanied by substantial reductions in the cutting waste (8.93%), carbon emissions (12.99%), and total costs (9.94%) compared with a previous study. The outcomes provide the industry with insights into further reducing rebar consumption and its related consequences. Applying the proposed algorithm to various construction projects will further amplify the corresponding benefits.