The article is devoted to the issues regarding assessment of the impact of changes in the delay in the feed direction on the dynamics of metal processing with metal-cutting machines. Here, for the first time, it is proposed that we take into account, when constructing models of the cutting control system, the real value of the delay value. It is this model that allows us to adequately consider the dynamics of the cutting process, by clarifying the effect of vibration regeneration. In this article, much attention is paid to describing the development of a measuring system that allows the calculation of the real value of the feed during cutting. It describes a series of experiments, and shows the results of data processing, using software developed by the authors. The studies conducted have shown that, in addition to the vibrations of the cutting tool in the feed direction, the vibration activity of the tool in the cutting direction plays an essential role in ensuring the regenerative effect. It should be noted that, currently, this is a new area of knowledge regarding processes in metalworking, and it requires further study.
This article discusses the issue of the joint use of neural network algorithms for data processing and deterministic mathematical models. The use of a new approach is proposed, to determine the discrepancy between data from a vibration monitoring system of the cutting process and the calculated data obtained by modeling mathematical models of the digital twin system of the cutting process. This approach is justified by the fact that some coordinates for the state of the cutting process cannot be measured, and the vibration signals measured by the vibration monitoring system (the vibration acceleration of the tip of the cutting tool) are subject to external disturbing influences. Both the experimental method and the Matlab 2022b simulation method were used as research methods. The experimental research method is based on the widespread use of modern analog vibration transducers, the signals from which undergo the process of digitalization and further processing in order to identify arrays of additional information required for virtual digital twin models. The results obtained allow us to formulate a new conceptual approach to the construction of systems for determining the degree of cutting tool wear, based on the joint use of computational virtual models of the digital twin system and data obtained from the vibration monitoring system of the cutting process.
The article is devoted to the issues of assessing the impact of changes in the delay value in the feed direction, what determines the regenerative nature of self-excitation of the cutting system, on the dynamics of metal processing on metal-cutting machines. It is this interconnected model of the cutting system that allows to identify the main dynamic effects that occur in the cutting system, including the effect of vibrations regeneration when cutting along the track. The article also has a section dedicated to the experiment on a real metalworking machine, on which vibrations of the top of the cutting wedge of the tool were measured and based on these data, a real calculation of the delay time and the magnitude of the change in the area of the cut layer was carried out, due to variations in the real feed. The conducted studies have shown that in addition to the vibrations of the cutting tool in the direction of feeding, the vibration activity of the tool in the direction of cutting plays an essential role in ensuring the regenerative effect. The delay time constant of the operator is formed, which determines the real value of the feed during cutting.
17 March 2025 in Metal Working and Material Science
Introduction. The most important factor determining the efficiency of metal cutting is the quality of the surface of the part obtained during cutting. The surface quality of a machined part is directly dependent on the vibration activity of the cutting tool, the amplitude of which is influenced by the complex evolutionary dynamics of the cutting process. In light of this, modern digital twin technology, which allows predicting the surface quality values of the parts using virtual models, is becoming an extremely relevant way to improve the efficiency in metalworking control systems. The purpose of the work. This study aims to improve the prediction accuracy of a digital twin system for the surface quality of the machined parts under conditions of increasing cutting tool wear. The paper examines: the dynamics of the turning process of metal parts, as well as a mathematical model describing the dynamics of tool vibrations during metal machining on lathes, considering the influence of the thermodynamic subsystem of the cutting system. Research methods. An experimental approach was employed, utilizing a author-designed measuring stand along with a modern inverted metallographic microscope LaboMet-I version 4, equipped with wide-angle lenses 5/20, having a 20 mm linear field of view, and a digital camera for microscopes Ucam-1400 with a 1.4 μm×1.4 μm matrix, and a contour profile recorder T4HD. Furthermore, the study used mathematical modeling of the dynamic cutting system in the Matlab environment, for which the authors developed a specialized data processing program. Results and discussion. Curves depicting the tool wear rate, changes in the quality parameters of the machined surface as functions of cutting path, and as a function of cutting tool wear are constructed. Dynamic indicators suitable for parametric identification of virtual digital twin models are determined. The structure of these models is established, and parametric identification is performed. Numerical modeling is conducted in the Matlab environment, based on the results of which a curve depicting the change in average arithmetic surface roughness as a function of increasing tool wear is constructed. The convergence of the results of field and numerical experiments is evaluated, which shows a high reliability of the surface quality prediction achievable through the use of digital twin systems.
The use of data processing algorithms based on neural networks in combination with deterministic mathematical models is considered. The pairing of these tw
Modern plant cultivation methods inherently should incorporate digital monitoring and control systems to enhance the efficiency of agricultural enterprises. Monitoring and precise measurement of the UV component of solar radiation is an important issue, yet it is often ignored in common weather stations and monitoring systems. UV radiation affects plant physiology, pollinator activity, risks of disease emergence, etc. Due to the lack of data on solar activity in this spectral range, it is impossible to correctly adapt protective measures or, conversely, supplemental lighting using UV lamps. Their integration into closed agricultural cultivation systems requires the optimization of algorithms. Existing UV radiation measurement systems are costly and do not solve the problem of continuous monitoring over large areas with the widespread use of artificial lighting sources. Thus, the relevant task is the creation of a distributed system for monitoring both solar and artificial UV radiation.