This investigation was attempted to introduce carbon nanotubes (CNTs) onto surface of copper powders in order to improve heat transfer performance of copper matrix for engineering application of electrical packaging materials. The Ni/MgO catalyst was formed on the copper powders surface by means of codeposition method. CVD technique was executed to fabricate uniform CNTs on copper powders and effect of reaction temperature on the morphology of CNTs was surveyed. The results showed that CNTs products on the copper powder surface were distributed uniformly even if reaction temperature was different. The diameter dimension of CNTs was within the scope of 30~60 nm. Growth behaviors of CNTs by CVD method were considered to be “tip-growth” mechanism. Raman spectra of CNTs proved that intensity ratio of D-band to G-band () increased as deposition reaction temperature increased, which implied that order degree of graphitic structure in synthesized CNTs improved.
Bone defects occurring for various reasons can lead to deformities and dysfunctions of the human body. Considering the need for clinical applications, it is essential for bone regeneration to exploit a scaffold with bioactive bone cement. In this study, we fabricated bioactive magnesium phosphate bone cement (BMPC) at room temperature; then, it was set at to °C and 100% humidity for 2 h. The process was as follows: Simulating a clinical environment, magnesium oxide (MgO) was formed by calcining basic magnesium carbonate (Mg2(OH)2CO3). MgO, potassium dihydrogen phosphate (KH2PO4) and carboxymethyl chitosan (C20H37N3O14, CMC) were mixed to form magnesium phosphate bone cement (MPC); then, monocalcium phosphate (Ca(H2PO4)2) was added to neutralize the alkaline product after MPC hydration to fabricate bioactive magnesium phosphate bone cement (BMPC). The influence of the doped content of Ca(H2PO4)2 on the properties of bone cement was discussed. The results showed that Ca(H2PO4)2 and CMC can adjust the setting time of bone cement to between 8 and 25 min. The compressive strength increased first and then decreased. After 48 h without additional pressure, the compressive strength reached the maximum value, which was about 38.6 MPa. Ca(H2PO4)2 and CMC can play a synergistic role in regulating the properties of BMPC. The BMPC was degradable in the simulated body fluid (SBF). The results of the cytotoxicity experiment and laser confocal microscopy experiment indicated that BMPC fabricated at room temperature had better biocompatibility and degradability, which was more consistent with clinical operation requirements. BMPC is a promising orthopedic material and is suitable for repairing bone defects.
In view of the surface engineering application of electrical contact materials, SiC ceramic particles were introduced into copper matrix composites by the hot-press sintering method for the sake of enhancing the service life of copper matrix electrical contact materials. Magnetron sputtering technology was exploited to form the continuous copper film on the β-SiC powders in order to improve interface wettability between SiC powder and copper matrix. The SiC@Cu powders were treated by magnetron sputtering technology. Then, dynamic deposit behavior was described according to SEM results. The phase constitution, fracture morphology, relative density, porosity, Vickers hardness, and coefficient of thermal expansion of SiC@Cu/Cu composites with different SiC@Cu addition were analyzed in detail. The results showed that SiC@Cu powders with higher fraction in the SiC@Cu/Cu composites would decrease relative density and increase porosity, so it resulted in improvement of Vickers hardness. The addition of SiC@Cu decreased CTE values of the SiC@Cu/Cu composite, especially at high-level fraction SiC@Cu powder.
9 March 2021 in International Journal of Photoenergy
The 7075 aluminum alloy was an important structural material in the field of aeronautics and astronautics. With the development of this field, the requirements for its comprehensive properties were increasing. A novel casting method, the impact jet solid-liquid compound casting, was adopted to fabricate the 3A21/7075 aluminum alloy cladding material. Retrogression and reaging (RRA) treatment was further applied to the 3A21/7075 aluminum alloy cladding material in order to investigate the influence of RRA on microstructure and microhardness of the 3A21/7075 aluminum alloy cladding material. Then, the electron backscattered diffraction (EBSD) technique and the transmission electron microscope (TEM) together with the energy dispersive spectrometer (EDS) and the hardness test were utilized to analyze the influence of RRA treatment on microstructure and hardness of the 3A21/7075 aluminum alloy cladding material. The research results showed the 3A21/7075 aluminum alloy cladding material had better deformability. The amount of fine and dispersed phases precipitated in grains was in favor of improving the comprehensive mechanical properties of the 3A21/7075 aluminum alloy cladding material. This research might provide data and a theoretical approach for the engineering application of the 3A21/7075 aluminum alloy cladding material.