Hu Ming

Hu Ming

Auto-generated profile, based on publicly available information

Hu Ming

College of Materials Science & Engineering, Jiamusi University, Jiamusi 154007, China

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2016 in Journal of Nanomaterials
Verified
Journal Article
Open access
PDF file
HMHu Ming
Hu Ming
DPDing Peiling
Ding Peiling
ZYZhang Yunlong
Zhang Yunlong
GJGao Jing
Gao Jing
RXRen Xiaoxue
Ren Xiaoxue
This investigation was attempted to introduce carbon nanotubes (CNTs) onto surface of copper powders in order to improve heat transfer performance of copper matrix for engineering application of electrical packaging materials. The Ni/MgO catalyst was formed on the copper powders surface by means of codeposition method. CVD technique was executed to fabricate uniform CNTs on copper powders and effect of reaction temperature on the morphology of CNTs was surveyed. The results showed that CNTs products on the copper powder surface were distributed uniformly even if reaction temperature was different. The diameter dimension of CNTs was within the scope of 30~60 nm. Growth behaviors of CNTs by CVD method were considered to be “tip-growth” mechanism. Raman spectra of CNTs proved that intensity ratio of D-band to G-band (ID/IG) increased as deposition reaction temperature increased, which implied that order degree of graphitic structure in synthesized CNTs improved.

25 February 2021 in International Journal of Photoenergy
Verified
Journal Article
Open access
PDF file
ZYZhang Yunlong
Zhang Yunlong
LWLi Wenbo
Li Wenbo
HMHu Ming
Hu Ming
YHYi Hongyong
Yi Hongyong
ZWZhou Wei
Zhou Wei
TLTang Lili
Tang Lili
In view of the surface engineering application of electrical contact materials, SiC ceramic particles were introduced into copper matrix composites by the hot-press sintering method for the sake of enhancing the service life of copper matrix electrical contact materials. Magnetron sputtering technology was exploited to form the continuous copper film on the β-SiC powders in order to improve interface wettability between SiC powder and copper matrix. The SiC@Cu powders were treated by magnetron sputtering technology. Then, dynamic deposit behavior was described according to SEM results. The phase constitution, fracture morphology, relative density, porosity, Vickers hardness, and coefficient of thermal expansion of SiC@Cu/Cu composites with different SiC@Cu addition were analyzed in detail. The results showed that SiC@Cu powders with higher fraction in the SiC@Cu/Cu composites would decrease relative density and increase porosity, so it resulted in improvement of Vickers hardness. The addition of SiC@Cu decreased CTE values of the SiC@Cu/Cu composite, especially at high-level fraction SiC@Cu powder.

9 March 2021 in International Journal of Photoenergy
Verified
Journal Article
Open access
PDF file
MHMing Hu
Ming Hu
XRXiaoxue Ren
Xiaoxue Ren
JSJianbo Sun
Jianbo Sun
ZYZhang Yunlong
Zhang Yunlong
The 7075 aluminum alloy was an important structural material in the field of aeronautics and astronautics. With the development of this field, the requirements for its comprehensive properties were increasing. A novel casting method, the impact jet solid-liquid compound casting, was adopted to fabricate the 3A21/7075 aluminum alloy cladding material. Retrogression and reaging (RRA) treatment was further applied to the 3A21/7075 aluminum alloy cladding material in order to investigate the influence of RRA on microstructure and microhardness of the 3A21/7075 aluminum alloy cladding material. Then, the electron backscattered diffraction (EBSD) technique and the transmission electron microscope (TEM) together with the energy dispersive spectrometer (EDS) and the hardness test were utilized to analyze the influence of RRA treatment on microstructure and hardness of the 3A21/7075 aluminum alloy cladding material. The research results showed the 3A21/7075 aluminum alloy cladding material had better deformability. The amount of fine and dispersed phases precipitated in grains was in favor of improving the comprehensive mechanical properties of the 3A21/7075 aluminum alloy cladding material. This research might provide data and a theoretical approach for the engineering application of the 3A21/7075 aluminum alloy cladding material.

1 September 2014
Verified
Conference Paper
Closed access
MHMing Hu
Ming Hu
SXShuhong Xie
Shuhong Xie
JZJiamnin Zhang
Jiamnin Zhang
JXJiauling Xue
Jiauling Xue
“Nan'ao Island ±160kV multiterminal flexible DC transmission Project” developed by China Southern Power Grid is China first project that HVDC submarine cable and land power cable with XLPE insulation have been applied. This paper demonstrates the simulation verification design of the insulation thickness and electric stress of the ±160kV DC cables for this project and proves that the electric stress at any point of insulation complies with the performance of insulation material. And the type test and prequalification test of ±160kV DC cable system are also introduced to prove the long-term reliability of DC power cable and factory splice.