Marianna Pires Barbosa

Dr. Marianna Pires Barbosa

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2024 in Materials
Verified
Journal Article
Open access
PDF file
ESEduardo Da Silva
Eduardo Da Silva
CACristiane Mariote Amaral
Cristiane Mariote Amaral
RJRenata Nunes Jardim
Renata Nunes Jardim
MBMarianna Pires Barbosa
Marianna Pires Barbosa
TRTiago Braga Rabello
Tiago Braga Rabello
The evaluation of water sorption and solubility is pivotal for the development of new resin-based restorative materials with the potential for clinical application. The purpose of the present study was to evaluate the influence of the specimen dimension, water immersion protocol, and surface roughness on the water sorption and solubility of three resin-based restorative materials. Disk-shaped specimens of 15 mm × 1 mm, 10 mm × 1 mm, and 6 mm × 1 mm were produced with a composite resin (Z100), a resin cement (RelyX ARC), and an adhesive system (Single Bond 2—SB2). The specimens were immersed in distilled water according to four protocols: ISO (all the specimens for each group were vertically immersed in 50 mL); IV-10 (the specimens were individually and vertically immersed in 10 mL); IH-10 (the specimens were individually and horizontally immersed in 10 mL); and IH-2 (the specimens were individually and horizontally immersed in 2 mL). The surface roughness (Sa and Sp) was evaluated using an atomic force microscope, and the degree of conversion was determined using FT-IR spectrometry. The specimen dimension and water immersion protocol had no effect on water sorption and solubility. For the three resin-based restorative materials, Sp was higher than Sa. The degree of conversion was not influenced by the specimen dimension. The variations in the specimen dimension and water immersion protocol compared to those determined by ISO 4049 did not prevent the comparison between the values of water sorption and solubility obtained for a given resin-based restorative material.

29 November 2023 in Materials
Verified
Journal Article
Open access
PDF file
MBMarianna Pires Barbosa
Marianna Pires Barbosa
TRTiago Braga Rabello
Tiago Braga Rabello
ESEduardo Da Silva
Eduardo Da Silva
Even after more than six decades of dental composite invention (1962), there is still controversial information about the time in which composite restorations should be polished in order to avoid marginal gap formation at the tooth–composite interface. The aim of the present study was to analyze the influence of adhesive strategy, the type of dental composite, and polishing time on marginal gap formation (%MG) at the tooth–composite interface. Class I-like cavities were hybridized with a universal adhesive system (Single Bond Universal) through two strategies: selective enamel etching (SEE) or self-etching mode (SEM). Cavities were filled with two types of dental composites: nanofilled (Z350) or bulk fill (Filtek One Bulk Fill—ONE), and polishing was performed immediately or delayed for 7 days (n = 5). %MG was evaluated by using a 3D laser confocal microscope. As flexural modulus (FM) and degree of conversion (DC%) are determinants of marginal integrity in dental composite restorations, these properties were evaluated for both composites. Data were analyzed by ANOVA and Tukey’s HSD test (α = 0.05). Cavities hybridized following the SEE strategy presented lower %MG (p < 0.05). Z350 showed higher %MG than ONE (p < 0.05). There was no difference in %MG between the polishing times when the SEE strategy was used (p > 0.05). Z350 presented higher FM than ONE (p < 0.05). DC% was found to be not significant (p > 0.05). The results suggest that selective enamel etching (SEE) is a better strategy for producing less %MG in composite restorations with enamel margins irrespective of the time in which the restoration is polished.