Indirect restorations in contact with free gingival margins or principally within the gingival sulcus, where the presence of organic acids produced by oral biofilm is higher, may present faster degradation of the resin-based cement pellicle.
This study evaluated the potential of a tri-functional monomer (trimethylolpropane trimethacrylate -TMPTMA) for inclusion in a dental composite organic matrix. Initially, four ternary matrixes with different concentrations (wt%) of bi-functional monomers [BisGMA (G), Bis-EMA (E) and TEGDMA (T)] were analyzed: GET523, GET532, EGT523 and EGT532 (the numbers (n) represent n×10 wt% of each monomer). The following properties were evaluated: degree of conversion, flexural strength, elastic modulus, hardness, absorption, solubility, diffusion coefficient of water and crosslink density. Based on the best overall results obtained for EGT532, all properties were re-evaluated in a matrix where TEGDMA (T) was replaced by a tri-functional monomer, TMPTMA (A)-EGA532. EGA532 presented the best results for flexural strength, hardness, absorption and crosslink density. EGT523, EGT532 and EGA532 presented the lowest diffusion coefficients of water. The overall results indicated that TMPTMA could be useful in formulating organic matrixes suitable for dental restorative composites.
1 December 2019 in Journal of the Mechanical Behavior of Biomedical Materials
The evaluation of water sorption and solubility is pivotal for the development of new resin-based restorative materials with the potential for clinical application. The purpose of the present study was to evaluate the influence of the specimen dimension, water immersion protocol, and surface roughness on the water sorption and solubility of three resin-based restorative materials. Disk-shaped specimens of 15 mm × 1 mm, 10 mm × 1 mm, and 6 mm × 1 mm were produced with a composite resin (Z100), a resin cement (RelyX ARC), and an adhesive system (Single Bond 2—SB2). The specimens were immersed in distilled water according to four protocols: ISO (all the specimens for each group were vertically immersed in 50 mL); IV-10 (the specimens were individually and vertically immersed in 10 mL); IH-10 (the specimens were individually and horizontally immersed in 10 mL); and IH-2 (the specimens were individually and horizontally immersed in 2 mL). The surface roughness (Sa and Sp) was evaluated using an atomic force microscope, and the degree of conversion was determined using FT-IR spectrometry. The specimen dimension and water immersion protocol had no effect on water sorption and solubility. For the three resin-based restorative materials, Sp was higher than Sa. The degree of conversion was not influenced by the specimen dimension. The variations in the specimen dimension and water immersion protocol compared to those determined by ISO 4049 did not prevent the comparison between the values of water sorption and solubility obtained for a given resin-based restorative material.
The aim of this study was to analyze the sorption and solubility of a nanofilled (Filtek Z350) and a midifilled (Filtek P60) resin composite in oral environment-like substances, in a simulated deep cavity. A cylindrical cavity prepared in a bovine incisor root was incrementally filled with resin composites. The obtained resin composite cylinders were cut perpendicularly to the axis to obtain 1-mm-thick discs that were divided into fifteen groups (n=5) according to depth (1, 2, 3, 4 and 5 mm) and immersion media (distilled water - DW, artificial saliva - AS and lactic acid - LA). The sorption and solubility were calculated based on ISO 4049:2000. Additionally, the degree of conversion (DC%) was calculated by FT-IR spectroscopy. Data were analyzed using multifactor analysis of variance (MANOVA) followed by Tukey's HSD post-hoc test and linear regression analysis (a=0.05). The DC% was higher for the midifilled resin composite and was negatively influenced by cavity depth (pAS>DW, (p