Large area multi-chip LED devices, such as chip-on-board (CoB) LEDs, require the combined use of chip-level multi-domain compact LED models (Spice-like compact models) and the proper description of distributed nature of the thermal environment (the CoB substrate and phosphor) of the LED chips. In this paper, we describe such a new numerical solver that was specifically developed for this purpose. For chip-level, the multi-domain compact modeling approach of the Delphi4LED project is used. This chip-level model is coupled to a finite difference scheme based numerical solver that is used to simulate the thermal phenomena in the substrate and in the phosphor (heat transfer and heat generation). Besides solving the 3D heat-conduction problem, this new numerical simulator also tracks the propagation and absorption of the blue light emitted by the LED chips, as well as the propagation and absorption of the longer wavelength light that is converted by the phosphor from blue. Heat generation in the phosphor, due to conversion loss (Stokes shift), is also modeled. To validate our proposed multi-domain model of the phosphor, dedicated phosphor and LED package samples with known resin—phosphor powder ratios and known geometry were created. These samples were partly used to identify the nature of the temperature dependence of phosphor-conversion efficiency and were also used as simple test cases to “calibrate” and test the new numerical solver. With the models developed, combined simulation of the LED chip and the CoB substrate + phosphor for a known CoB LED device is shown, and the simulation results are compared to measurement results.
In this paper the magnetic nanoparticle aggregation procedure in a microchannel in the presence of external magnetic field is investigated. The main goal of the work was to establish a numerical model, capable of predicting the shape of the nanoparticle aggregate in a magnetic field without extreme computational demands. To that end, a specialized two-phase CFD model and solver has been created with the open source CFD software OpenFOAM. The model relies on the supposed microstucture of the aggregate consisting of particle chains parallel to the magnetic field. First, the microstructure was investigated with a micro-domain model. Based on the theoretical model of the particle chain and the results of the micro-domain model, a two-phase CFD model and solver were created. After this, the nanoparticle aggregation in a microchannel in the field of a magnet was modeled with the solver at different flow rates. Measurements with a microfluidic device were performed to verify the simulation results. The impact of the aggregate on the channel heat transfer was also investigated.
15 February 2018 in Periodica Polytechnica Electrical Engineering and Computer Science
In this paper we present a new, direct computational method for calculating thermal transfer impedances between two separate locations of a given physical structure, aimed at the implementation into a field-solver based on the SUNRED (SUccessive Node REDuction) algorithm. We tested the method symbolically with a simple 2D example with multiple combinations of Dirichlet and Neumann type boundary conditions. Also, for time domain transient analysis different types of thermal loads such as prescribed unit-step change in dissipation or temperature were assumed. A model of a typical MCPCB assembled LED was also created. With that model we studied the inverse problem of predicting the thermal conditions at the junction (the "driving point") from the transient signal measured at the thermal test point on the MCPCB (the "monitoring point") which is a typical task in simple LED thermal management designs. Results obtained by the proposed new calculation method and results obtained by conventional numerical simulations differ less than the uncertainty of the traditional solution method itself. The drawback of the accuracy is the high computational cost. This increased computational need can be mitigated by introducing the combination of the balanced model reduction and the SUNRED algorithms
In this paper, a novel method is presented to estimate the parameters of the SPICE-like multi-domain model of light-emitting diode (LED) chips developed and proposed by the Delphi4LED project. The proposed estimation algorithm employs a modified Nelder-Mead method, as the gradient methods and the original version of Nelder-Mead fail to properly handle this problem. By using the new, modified Nelder-Mead method presented in this paper the parameters are estimated faster, compared to the previously used brute-force algorithm-based parameter extraction process, allowing the same precision of the SPICE-like multi-domain LED model. The modification of the parameter extraction procedure also allows speeding up and simplifying the multi-domain LED characterization method proposed earlier by the Delphi4LED project. The speed and robustness of the new model eliminate the need for time-consuming junction temperature control during measurements by employing a novel extraction strategy that seeks the global minimum, rather than relying on the composition of marginal minima.