Ali Kareem Abdulrazzaq

Mr. Ali Kareem Abdulrazzaq

Department of Electron Devices, Budapest University of Technology and Economics
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2020 in Solar Energy
Verified
Journal Article
Closed access
Ali Kareem AbdulrazzaqAli Kareem Abdulrazzaq
Ali Kareem Abdulrazzaq
GBGyörgy Bognár
György Bognár
BPBalázs Plesz
Balázs Plesz

10 February 2025 in Journal of Computational Electronics
Verified
Journal Article
Open access
PDF file
Ali Kareem AbdulrazzaqAli Kareem Abdulrazzaq
Ali Kareem Abdulrazzaq
GBGyörgy Bognár
György Bognár
PBPlesz Balázs
Plesz Balázs
Accurate modeling of the operational behavior of photovoltaic systems is crucial to optimizing and predicting system performance. One of the well-established and widely used modeling techniques is the single-diode equivalent circuit that delivers a sufficiently accurate description of the electric behavior of both photovoltaic cells and modules under various operational conditions. The single-diode model uses five parameters to reproduce the I-V curve for specific operational conditions. However, these five parameters must be extracted from measured or simulated I-V curves. This paper proposes a novel, accurate, and fast method for extracting the single-diode model’s five parameters from measured I-V curves based on a genetic algorithm combined with particle swarm optimization to find the optimal controlling parameters of the genetic algorithm. This approach results in a significant performance improvement in accuracy and convergence speed. The paper also proposes a concept for determining the optimum number of current–voltage data points in the I-V curve, enabling an optimum trade-off between a sufficiently high accuracy and computational costs. Finally, the effect of different objective function formulations on the result has been investigated by comparing the usage of three different objective functions: the implicit form of the single-diode model, the Lambert W-function-based formulation of the explicit single-diode model, and a system of equations based on least square fitting. From the results, it could be concluded that the implicit formulation of the single-diode model delivered the best results compared to the two other formulations. Performance evaluations showed significantly lower error values than recent literature, with mean percent errors of 0.038%, 0.34%, and 0.87% received for the investigated monocrystalline cell, poly-crystalline module, and amorphous module, respectively. The computational cost was reduced by more than 60% after determining the optimum number of I-V points per curve, which was in the range of 20–30 points for each measured curve.

29 June 2020 in Energies
Verified
Journal Article
Open access
PDF file
Ali Kareem AbdulrazzaqAli Kareem Abdulrazzaq
Ali Kareem Abdulrazzaq
BPBalázs Plesz
Balázs Plesz
GBGyörgy Bognár
György Bognár
Temperature has a significant effect on the photovoltaic module output power and mechanical properties. Measuring the temperature for such a stacked layers structure is impractical to be carried out, especially when we talk about a high number of modules in power plants. This paper introduces a novel thermal model to estimate the temperature of the embedded electronic junction in modules/cells as well as their front and back surface temperatures. The novelty of this paper can be realized through different aspects. First, the model includes a novel coefficient, which we define as the forced convection adjustment coefficient to imitate the module tilt angle effect on the forced convection heat transfer mechanism. Second, the new combination of effective sub-models found in literature producing a unique and reliable method for estimating the temperature of the PV modules/cells by incorporating the new coefficient. In addition, the paper presents a comprehensive review of the existing PV thermal sub-models and the determination expressions of the related parameters, which all have been tested to find the best combination. The heat balance equation has been employed to construct the thermal model. The validation phase shows that the estimation of the module temperature has significantly improved by introducing the novel forced convection adjustment coefficient. Measurements of polycrystalline and amorphous modules have been used to verify the proposed model. Multiple error indication parameters have been used to validate the model and verify it by comparing the obtained results to those reported in recent and most accurate literature.

25 March 2021 in Pollack Periodica
Verified
Journal Article
Open access
PDF file
Ali Kareem AbdulrazzaqAli Kareem Abdulrazzaq
Ali Kareem Abdulrazzaq
GBGyörgy Bognár
György Bognár
BPBalázs Plesz
Balázs Plesz
This paper presents a combined electro-thermal model to serve the aim of accurate output power prediction of photovoltaic systems, based on the concept of the thermal energy balance. The electrical sub-model is built based on fitting a surface to the current-voltage curves collected under wide range temperatures and irradiances. For this purpose, the current-voltage characteristic curves are reproduced using two different methods. The thermal sub-model considers all the effective heat transfer mechanisms to estimate the photovoltaic module junction temperature. The Newton-Raphson iterative method is used as a solving algorithm to calculate the photovoltaic junction temperature. The collected results prove the applicability of the model under a wide range of environmental conditions.

15 August 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MNMárton Németh
Márton Németh
JHJános Hegedüs
János Hegedüs
GHGusztáv Hantos
Gusztáv Hantos
Ali Kareem AbdulrazzaqAli Kareem Abdulrazzaq
Ali Kareem Abdulrazzaq
PAPoppe András
Poppe András
In this paper, a novel method is presented to estimate the parameters of the SPICE-like multi-domain model of light-emitting diode (LED) chips developed and proposed by the Delphi4LED project. The proposed estimation algorithm employs a modified Nelder-Mead method, as the gradient methods and the original version of Nelder-Mead fail to properly handle this problem. By using the new, modified Nelder-Mead method presented in this paper the parameters are estimated faster, compared to the previously used brute-force algorithm-based parameter extraction process, allowing the same precision of the SPICE-like multi-domain LED model. The modification of the parameter extraction procedure also allows speeding up and simplifying the multi-domain LED characterization method proposed earlier by the Delphi4LED project. The speed and robustness of the new model eliminate the need for time-consuming junction temperature control during measurements by employing a novel extraction strategy that seeks the global minimum, rather than relying on the composition of marginal minima.

10 October 2019 in Periodica Polytechnica Electrical Engineering and Computer Science
Verified
Journal Article
Open access
PDF file
Ali Kareem AbdulrazzaqAli Kareem Abdulrazzaq
Ali Kareem Abdulrazzaq
GBGyörgy Bognár
György Bognár
BPBalázs Plesz
Balázs Plesz
Accurate and reliable PV device modelling is a fundamental tool to optimize system performance. The regular operation of the PV system in an outdoor condition implies the need for a model that relate the environmental effects. This paper presents a new, simple, and efficient method for constructing the I-V characteristics for a PV cell incorporating the environmental conditions. The proposed model is based on the idea of dividing the voltage axis of the solar cell I-V characteristics using a fixed time interval. For each voltage interval point, a two-dimensional current matrix is calculated, corresponding different irradiance conditions and temperatures. Polynomial surface fitting is used to build sub-models for each voltage interval. The current two-dimensional matrix, for each point, is calculated by two different methods. The first method is based on linear interpolation of the measured I-V curves. The second method uses pre-extracted five parameters for the well known single diode model at a wide range of environmental conditions. The developed modelling technique provides accurate results compared with the measured data for a mono-crystalline solar cell.