Yan Xu

Prof. Yan Xu

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 May 2021 in Materials Letters
Verified
Journal Article
Closed access
YCYanKun Chen
YanKun Chen
JZJianping ZHOU
Jianping ZHOU
YZyan zhang
yan zhang
YXYan Xu
Yan Xu
YBYang Bao
Yang Bao

7 February 2018 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
KWKedian WANG
Kedian WANG
JZJianping ZHOU
Jianping ZHOU
KWKedian Wang
Kedian Wang
YXYan Xu
Yan Xu
TWTianbo Wu
Tianbo Wu
The short electric arc machining technology is a technical category of electrical machining in the special machining industry. It further improves machining efficiency (1.92 × 105 mm3/min) in comparison to other electrical machining. In short electric arc machining, the electrode materials directly affect the surface quality of the workpiece, electrode loss, and dimensional accuracy. Therefore, the selection of the electrode material is particularly important. Using the nickel-based superalloy GH4169 machining as the research object, the study aimed to improve the material removal rate, while reducing the electrode loss. The experimental research on the short electric arc machining properties (machining surface quality, inter-polar voltage and current waveform, electrode loss analysis, surface morphology, microstructure, chemical components analysis, etc.) of four types of tool electrode materials (graphite, copper, Q235, and aluminum) separated by two groups was conducted, in the first group: under the certain technological parameter, machining the GH4169 by four kinds of tool electrode materials respectively. In the second group, the influence of different tool electrode materials on the material removal rate was studied by using graphite and copper as the tool electrode materials under the different process parameters of discharge current, pulse time, pulse interval, and air pressure. The results show that the mechanical properties of the electrode materials differed due to the different thermal properties of the electrode materials under the same process parameters. Furthermore, the different physical properties of the electrode material caused different effects on the residual heat, resulting in differences in the material removal rate. Under most of the discharge conditions, MRR occupied a large proportion in the graphite electrode, and the relative mass loss of the electrode was about 16.7% of that of copper, providing a solid theoretical basis for the electrode selection of the short electric arc machining hard surface materials.

1 December 2021 in Materials Letters
Verified
Journal Article
Closed access
YGYidi Gao
Yidi Gao
YZyan zhang
yan zhang
JLJing Li
Jing Li
LKLiu Kai
Liu Kai
YXYan Xu
Yan Xu
JZJianping ZHOU
Jianping ZHOU

22 November 2024 in Agriculture
Verified
Journal Article
Open access
PDF file
XCXiaokang Chen
Xiaokang Chen
GDGenggeng Dong
Genggeng Dong
Xiangpeng FanXiangpeng Fan
Xiangpeng Fan
YXYan Xu
Yan Xu
TLTongshe Liu
Tongshe Liu
HJHong Jiang
Hong Jiang
Among the challenges posed by real orchard environments, where the slender new plum fruit stalks exhibit varying postures and share similar coloration with surrounding leaves and branches, the significant obscuration caused by leaves leads to inaccurate segmentation of the fruit stalks, thereby complicating the precise localization of picking points and other related issues. This paper proposes a method for new plum fruit stalk recognition and picking point localization based on the improved DeepLabv3+ model. Firstly, it employs the lightweight MobileNetv2 as the backbone feature extraction network. Secondly, the Convolutional Block Attention Module (CBAM) is integrated into the decoder to enhance the model’s ability to extract key features of the fruit stalks. Moreover, dense atrous spatial pyramid pooling (DenseASPP) is utilized to replace the original ASPP module, thereby reducing segmentation leakage. Finally, a picking point localization method is designed based on a refinement algorithm and an endpoint detection algorithm to meet the specific picking demands of new plum, identifying the endpoints along the skeletal line of the fruit stalks as the optimal picking points. The experimental results demonstrate that the mean intersection over union (MIoU) and mean pixel accuracy (MPA) of the enhanced DeepLabv3+ model are 86.13% and 92.92%, respectively, with a model size of only 59.6 MB. In comparison to PSPNet, U-Net, and the original DeepLabv3+ model, the MIoU improves by 13.78, 0.34, and 1.31 percentage points, while the MPA shows enhancements of 15.35, 1.72, and 1.38 percentage points, respectively. Notably, with the endpoint of the fruit stalk’s skeletal structure designated as the picking point for new plums, the localization success rate reaches 88.8%, thereby meeting the requirements for precise segmentation and picking point localization in actual orchard environments. Furthermore, this advancement offers substantial technical support for the research and development of new plum harvesting robots.

23 July 2023 in Metals
Verified
Journal Article
Open access
PDF file
YBYang Bao
Yang Bao
RXRuilei Xue
Ruilei Xue
JZJianping ZHOU
Jianping ZHOU
YXYan Xu
Yan Xu
In the welding process of thick plate narrow gap pulse gas metal arc welding (P-GMAW) overhead welding station, the arc characteristics and droplet transfer behavior that become more complex due to the combined effects of narrow gap groove, gravity, and welding torch oscillation. The welding stability is more difficult to control. High-speed imaging and electrical signal acquisition systems were established to observe and record the arc behavior and droplet transfer during the welding process at different oscillation widths, further revealing the formation mechanism of welding seam in narrow gap P-GMAW overhead welding station. Research has found that with an increased oscillation width, the arc deflects towards the sidewall from a trumpet-shaped symmetrically distributed around the center of the groove at an increasing deflection angle, and the droplet transfer changes from one droplet per pulse to multiple droplets per pulse, resulting in defects such as lack of sidewall fusion and undercutting of the weld seam. Based on the welding process discussed in this study, it is recommended to use an oscillation width of 2.6 mm.