Saheed Tijani

Dr. Saheed Tijani

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 April 2018 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Open access
DMDaniele Montanari
Daniele Montanari
GCGerardo Castellano
Gerardo Castellano
EKEhsan Kargaran
Ehsan Kargaran
GPGiacomo Pini
Giacomo Pini
STSaheed Tijani
Saheed Tijani
RCRinaldo Castello
Rinaldo Castello
Antenna-coupling group delay limits the cancellation bandwidth of conventional self-interference cancellers (SICs), making it difficult to ensure isolation in both transmit (TX) and receive (RX) bands. Isolation over both bands is achieved in the dual-path receiver architecture proposed in this paper. The main path consists of a highly linear current-mode RX with a passive RF SIC. The auxiliary path implements a notch in the TX band followed by an adaptive digital equalizer whose output is used to suppress the TX noise leakage in the RX band. The main and auxiliary receiver prototypes, implemented in 28-nm CMOS technology, operate between 1 and 2 GHz, occupy an area of 0.51 and 0.12 mm 2 , and have a power dissipation of 32-40 and 26-64 mW, respectively. The stand-alone RX has a noise figure (NF) of 4-5 dB and an out-of-band IIP3 of 18 dBm. Turning on the passive canceller results in an effective IIP3 of 25-29 dBm and a degradation of the NF of less than 0.8 dB. Thanks to its high dynamic range, the auxiliary path suppresses the TX noise by >29 dB while degrading the RX NF by only 1 dB at 23-dBm TX output power.

1 June 2017
Verified
Conference Paper
Closed access
EKE. Kargaran
E. Kargaran
STSaheed Tijani
Saheed Tijani
GPG. Pini
G. Pini
DMD. Manstretta
D. Manstretta
RCR. Castello
R. Castello
Saw-Less Frequency Division Duplexing and Full-Duplex transceivers require very high receiver linearity. Self-Interference Cancellation can relax the specification but results in very high power. We propose a low-power direct-conversion single-ended receiver with passive SIC. A 28 nm CMOS prototype achieves an effective IIP3 > 25 dBm for both IB and OOB SI with only 20 dB cancellation and 25 dB isolation. Power consumption is 25mW, active area is 0.5 mm2.

13 May 2021 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
MJMohsen Javadi
Mohsen Javadi
HMHossein Miar-Naimi
Hossein Miar-Naimi
STSaheed Tijani
Saheed Tijani
DMDanilo Manstretta
Danilo Manstretta
RCRinaldo Castello
Rinaldo Castello
A modified noise/nonlinearity cancellation low-noise transconductance amplifier (LNTA) based on an inductively degenerated common-source stage is proposed to improve linearity. The linearity of the proposed LNTA is analyzed using the Volterra series yielding closed-form equations for the third-order input intercept point (IIP3) that shows excellent matching with the simulation results. The derived equations for noise figure (NF) and IIP3 are simple enough to be used for design optimization. Calculations and simulation results show that the proposed LNTA is more linear than a conventional one, while NF approximately remains unchanged. Another feature of the proposed noise-canceling LNTA is that no additional baseband recombination stage is needed, leading to reduced complexity in the receiver baseband stage. The NF and out-of-band (OOB) IIP3 of the receiver is about 3.3 dB and more than 20 dBm, respectively. The receiver consumes 10.5 mA from 1.8-V supply voltage. The current consumption of the LO divider is 6.5 mA from a dedicated 1-V supply voltage.

Verified
Journal Article
Open access
PDF file
STSaheed Tijani
Saheed Tijani
DMDanilo Manstretta
Danilo Manstretta
An active self-interference (SI) cancellation technique for SAW-less receiver linearity improvement is proposed. The active canceler combines programmable gain and phase in a single stage and is co-designed with a highly-linear LNA, achieving low noise and low power. A cross-modulation mechanism of the SI canceler is identified and strongly suppressed thanks to the introduction of an internal resistive feedback, enabling high effective receiver IIP3. TX leakage of up to −4 dBm of power is suppressed by over 30 dB at the input of the LNA, with benefits for the entire receiver in terms of IIP3, IIP2, and reciprocal mixing. The design was done in a 40 nm CMOS technology. The system, including receiver and active SI canceler, consumes less than 25 mW of power. When the canceler is enabled, it has an NF of 3.9–4.6 dB between 1.7 and 2.4 GHz and an effective IIP3 greater than 35 dBm.

1 September 2018 in Integration
Verified
Journal Article
Closed access
ACArianna Coccia
Arianna Coccia
STSaheed Tijani
Saheed Tijani
DMDanilo Manstretta
Danilo Manstretta
RCRinaldo Castello
Rinaldo Castello

1 December 2015
Verified
Conference Paper
Closed access
STSaheed Tijani
Saheed Tijani
DMDanilo Manstretta
Danilo Manstretta
A receiver front-end based on an active self-interference canceler is presented. The active canceler combines programmable gain and phase in a single stage and was co-designed with a highly-linear LNA, achieving low noise and low power. A cross-modulation mechanism of Self Interference (SI) canceler was identified and strongly suppressed thanks to internal resistive feedback, enabling high effective IIP3 with respect to TX leakage. TX leakage of up to -4dBm of power is suppressed by over 30dB at the input of the LNA, with benefits for the entire receiver in terms of IIP3, IIP2 and reciprocal mixing. The LNA+canceler, designed in a 40nm CMOS technology, consumes <;25mW has a NF of 2.2-3.1dB and an IIP3 of 38dBm with -8dBm TX leakage.