Ehsan Kargaran

Dr. Ehsan Kargaran


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2019 in IEEE Solid-State Circuits Letters
Verified
Journal Article
Closed access
EKEhsan Kargaran
Ehsan Kargaran
BGBenqing Guo
Benqing Guo
DMDanilo Manstretta
Danilo Manstretta
RCRinaldo Castello
Rinaldo Castello
This paper presents a highly efficient low-IF receiver front-end for IoT applications. The low-noise trans-impedance amplifier (LNTA) combines a transformer-based network for scaling up the source impedance together with passive gm-boosting and current-reuse techniques to achieve better noise and 12x current saving compared with a Common Gate (CG) stage. A complex channel-selection filter with center frequency and passband of 2 and 1.4 MHz respectively is implemented after the passive mixer with a gm-boosted CG stage. Built in 28 nm CMOS, the proposed receiver occupies an active area of 0.1 mm2, it is supplied with 0.9 V and consumes only 350 μW, while showing a minimum NF of 6.2 dB at the channel of interest. The RF performance of the proposed receiver is very competitive with state-of-the-art ultra-low-power receivers, while it consumes the lowest power.

4 December 2017 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
EKEhsan Kargaran
Ehsan Kargaran
DMDanilo Manstretta
Danilo Manstretta
RCRinaldo Castello
Rinaldo Castello
To meet the requirements of wearable wireless sensor networks, the power dissipation of the RF transceiver has to be drastically reduced. This paper presents two ultra-low power low noise amplifiers (LNAs) with RF performance exceeding the requirement of the intended application. In the first LNA, by reusing the current several times and employing passive gm boosting, the LNA input impedance is reduced by a factor of 24 compared with a single transistor using the same current. The feasibility of passive gm boosting for designing an ultra-low supply voltage LNA is also investigated. Limitations of both LNAs, including NF, non-linearity, and stability in a 40-nm CMOS technology are also investigated. The proposed LNAs consume only 30 μW of power, operate with 0.8 V and 0.18 V and show NF of 3.3 and 5.2 dB, respectively. Using a widely accepted figure-of-merit for LNAs, the proposed circuit is almost three times better than the best previously reported sub-mW LNA.

19 April 2018 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Open access
DMDaniele Montanari
Daniele Montanari
GCGerardo Castellano
Gerardo Castellano
EKEhsan Kargaran
Ehsan Kargaran
GPGiacomo Pini
Giacomo Pini
STSaheed Tijani
Saheed Tijani
RCRinaldo Castello
Rinaldo Castello
Antenna-coupling group delay limits the cancellation bandwidth of conventional self-interference cancellers (SICs), making it difficult to ensure isolation in both transmit (TX) and receive (RX) bands. Isolation over both bands is achieved in the dual-path receiver architecture proposed in this paper. The main path consists of a highly linear current-mode RX with a passive RF SIC. The auxiliary path implements a notch in the TX band followed by an adaptive digital equalizer whose output is used to suppress the TX noise leakage in the RX band. The main and auxiliary receiver prototypes, implemented in 28-nm CMOS technology, operate between 1 and 2 GHz, occupy an area of 0.51 and 0.12 mm 2 , and have a power dissipation of 32-40 and 26-64 mW, respectively. The stand-alone RX has a noise figure (NF) of 4-5 dB and an out-of-band IIP3 of 18 dBm. Turning on the passive canceller results in an effective IIP3 of 25-29 dBm and a degradation of the NF of less than 0.8 dB. Thanks to its high dynamic range, the auxiliary path suppresses the TX noise by >29 dB while degrading the RX NF by only 1 dB at 23-dBm TX output power.

6 September 2021 in IEEE Open Journal of the Solid-State Circuits Society
Verified
Journal Article
Open access
EKEhsan Kargaran
Ehsan Kargaran
DMDanilo Manstretta
Danilo Manstretta
RCRinaldo Castello
Rinaldo Castello
Internet-of-Things (IoT) and Wireless sensor networks (WSNs) require very low power transceivers. This paper presents techniques for minimizing power consumption of receiver (RX) frontends for short range wireless links. Two key approaches, i.e., current reuse and supply voltage reduction are compared. Different RX architectures such as direct-conversion, low-IF, sliding IF as well as phase-tracking RX, are compared, emphasizing their potential and limitations when targeting sub-mW RX power dissipation. Low-power design techniques for LNA, frequency generation blocks and baseband amplifiers are presented. As a case study, an efficient low-IF RX front-end for IoT is described in detail. In 28 nm CMOS, such a receiver occupies an active area of 0.1 mm 2 and consumes only $350~{\mu }\text{W}$ from a 0.9 V supply while showing a minimum in band NF of 6.2 dB. The achieved performance is very competitive with state-of-the-art ultra-low-power receivers, while consuming the lowest power.

1 April 2019 in Microelectronics Journal
Verified
Journal Article
Closed access
EKEhsan Kargaran
Ehsan Kargaran
DMDanilo Manstretta
Danilo Manstretta
RCRinaldo Castello
Rinaldo Castello

17 January 2018 in Micromachines
Verified
Journal Article
Open access
PDF file
EKEhsan Kargaran
Ehsan Kargaran
DMDanilo Manstretta
Danilo Manstretta
RCRinaldo Castello
Rinaldo Castello
Wireless medical body-area networks are used to connect sensor nodes that monitor vital parameters. The radio consumes a large portion of the sensor energy budget, and hence its power dissipation should be minimized. The low-noise amplifier (LNA) is an important component of the receiver, and must guarantee low-noise amplification and impedance matching. In this work, an ultra-low-voltage ultra-low-power LNA is proposed that, thanks to the proposed transformer-based gate boosting technique, has a reduced current consumption of only 160 μA and can operate with a supply as low as 0.18 V. The LNA was designed using 40 nm Complementary Metal-Oxide Semiconductor (CMOS) technology and features a voltage gain of 14 dB, 5.2 dB NF and −8.6 dBm IIP3. This performance is comparable to a prior work by the same authors, but with the minimum supply voltage reduced by a factor of 4x.