In this work, the numerical and experimental analysis on the use of thinned fiber Bragg gratings as refractive index sensors have been carried out. Wet chemical etching in a buffered hydrofluoric acid solution was used for sensor fabrication. Experimental characterization for an almost full etched cladding sensor is presented demonstrating good agreement with numerical results and resolutions of /spl ap/10/sup -5/ and /spl ap/10/sup -4/ for outer refractive index around 1.45 and 1.333, respectively.

We present a technique for dynamic strain measurements in optical fibers based on the stimulated Brillouin scattering interaction between two counterpropagating optical pulses. The technique allows for a high sampling rate and permits to addressing dynamically and randomly the position at which vibration is measured. Preliminary experimental results carried out with a perturbation frequency up to $98\mathrm{Hz}$ demonstrate the validity of the proposed technique.

In this paper, we demonstrate high spatial (≈3 cm) and spectral (≈30 MHz) resolution Brillouin sensing by use of Brillouin optical frequency-domain analysis (BOFDA) and signal processing. An iterative method is employed to correct the acquired data from spurious effects associated to acoustic wave modulation and relevant in the high spatial resolution regime. Experimental tests demonstrate that the proposed algorithm allows to reconstruct the Brillouin shift profile with the full spatial resolution allowed by the system bandwidth.

In the last years, fiber optic sensors have been widely exploited for several sensing applications, including static and dynamic strain measurements up to acoustic detection. Among these, fiber Bragg grating sensors have been indicated as the ideal candidate for practical structural health monitoring in the light of their unique advantages over conventional sensing devices. Although this class of sensors has been successfully tested for static and low-frequency measurements, the identification of sensor performances for high-frequency detection, including acoustic emission and ultrasonic investigations, is required. To this aim, the analysis of feasibility on the use of fiber Bragg grating sensors as ultrasonic detectors has been carried out. In particular, the response of fiber Bragg gratings subjected to the longitudinal ultrasonic (US) field has been theoretically and numerically investigated. Ultrasonic field interaction has been modeled, taking into account the direct deformation of the grating pitch combined with changes in local refractive index due to the elasto-optic effect. Numerical results, obtained for both uniform and Gaussian-apodized fiber Bragg gratings, show that the grating spectrum is strongly influenced by the US field in terms of shape and central wavelength. In particular, a key parameter affecting the grating response is the ratio between the US wavelength and the grating length. Normal operation characterized by changes in the wavelength of undistorted Bragg peak is possible only for US wavelengths longer than the grating length. For US wavelengths approaching the grating length, the wavelength change is accompanied by subpeaks formation and main peak amplitude modulation. This effect can be attributed to the nonuniformity of the US perturbation along the grating length. At very high US frequencies, the grating is not sensitive any longer. The results of this analysis provide useful tools for the design of grating-based ultrasound sensors for meeting specific requirements in terms of field intensity and frequencies.

In this paper, the inverse scattering problem for dielectric objects in a two-dimensional half-space geometry is dealt with. The discussion is worked out in the framework of the linear model of the Born Approximation (BA) and the role of the measurement configuration is investigated with regard to the information content of the scattered field data. In particular, the configurations analyzed are multiview-multistatic, multibistatic and multistatic with a single view, all exploiting a frequency diversity and with the observation line at the interface. The comparison shows that the multibistatic configuration seems to offer a good compromise between the required measurement time, the computational "burden" and the quality of the achievable results.

We demonstrate a Brillouin optical frequency-domain reflectometry (BOFDR) technique, which can measure the strain and/or temperature along an optical fiber with one-end access, by detecting the spontaneous Brillouin scattering from a sinusoidally modulated pump light. Compared to the Brillouin optical frequency-domain analysis (BOFDA), we show that BOFDR measurements are free from the distorting components related to acoustic wave modulation, thus simplifying data processing.