Dmitry Vladimirovich Pronichev

Dr. Dmitry Vladimirovich Pronichev

orcid

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2016 in FME Transactions
Verified
Journal Article
Closed access
PDF file
YTYuriy Trykov
Yuriy Trykov
LGLeonid Gurevich
Leonid Gurevich
DPDmitry Vladimirovich Pronichev
Dmitry Vladimirovich Pronichev
MTMikhail Trunov
Mikhail Trunov
The study presents experimental investigations of the contact hardening effect of thin Cu and Nb interlayers in laminated Ti/Steel composites. The four layer Ti-Cu-Nb-Steel with various Nb and Cu interlayer thickness values was obtained via explosion welding and subsequently heat treated at 600°C for 1.5 hr. The evolution of the microstructure of the interfaces between bonded metals before and after heat treatment was studied during composites tensile loading. FEM simulation was carried out to determine the critical value of the relative interlayer thickness at which the composite tensile strength in transverse to the bond interface direction is higher than of Cu.

20 October 2017 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
VSV G Shmorgun
V G Shmorgun
OSO V Slautin
O V Slautin
DPDmitry Vladimirovich Pronichev
Dmitry Vladimirovich Pronichev
VKVitaliy Pavlovich Kulevich
Vitaliy Pavlovich Kulevich
It is shown that the phase transformations in the coating of the Fe-Al system produced by explosion welding of an aluminum AD1 with steel St3 and double occur in the following sequence: Fe 2 Al 5 → FeAl 2 → FeAl → Fe 3 Al → Fe (Al). They are accompanied by an increase in its thickness. The layered FeAl / Fe 3 Al / Fe (Al) coating on the inter-phase FeAl / Fe 3 Al boundary formed on a steel basis is porous, and inclusions of sulphides of manganese are present in alumina Fe 3 Al. The layered FeAl / Fe 3 Al / Fe (Al) coating on the steel base has a porous structure at the FeAl / Fe 3 Al interface, and inclusions of manganese sulfides in the Fe 3 Al aluminide region.

24 September 2014 in Materials Science
Verified
Journal Article
Open access
PDF file
YTYuriy Trykov
Yuriy Trykov
LGLeonid Gurevich
Leonid Gurevich
DPDmitry Vladimirovich Pronichev
Dmitry Vladimirovich Pronichev
MTMikhail Trunov
Mikhail Trunov
Influence of Strain-Hardened Zones and Intermetallic Layers of Explosion Welded and Heat Treated Al/Cu Laminated Metal Composites on the Evolution of Thermal Conductivity Coefficient

1 January 2016 in Inorganic Materials: Applied Research
Verified
Journal Article
Closed access
DPDmitry Vladimirovich Pronichev
Dmitry Vladimirovich Pronichev
LGL. M. Gurevich
L. M. Gurevich
YTYu. P. Trykov
Yu. P. Trykov
MTM. D. Trunov
M. D. Trunov

13 November 2023 in Metals
Verified
Journal Article
Open access
PDF file
LGLeonid Moiseevich Gurevich
Leonid Moiseevich Gurevich
DPDmitry Vladimirovich Pronichev
Dmitry Vladimirovich Pronichev
OSOleg V. Slautin
Oleg V. Slautin
VTViktoriya V. Tikhaeva
Viktoriya V. Tikhaeva
The growing interest in intermetallic and metal–intermetallic materials and coatings is based on the number of favorable properties they possess, primarily mechanical. However, the lack of data on their corrosion resistance has largely limited their scope of application. In this study, the corrosion destruction mechanisms of coatings formed on substrates made of AISI 321 steel and Aluchrom W (fechralloy) were investigated. The coatings were created by alloying in an aluminum melt followed by diffusion annealing to form the ultimate intermetallic structure. Corrosion resistance was studied under cyclic exposure to a humid marine atmosphere simulator and potentiostatic tests in an aqueous NaCl solution. Corrosion destruction parameters were determined, and mechanisms for each type of coating were revealed. The conducted studies allowed us to determine the electrochemical parameters of the corrosion destruction process and its mechanisms. It was shown that the corrosion rates during potentiostating for coatings on substrates Cr15Al5 and 12Cr18Ni10Ti differed by almost twofold. Two different mechanisms of corrosion are proposed. The first is associated with the formation of Al2O3 and MgO oxide films, which at the initial stage protect only local areas of the coating surface on Cr15Al5. The second is determined by the diffusion of titanium atoms during annealing to the coating surface on a 12Cr18Ni10Ti steel substrate with the formation of TiC carbide at the grain boundaries.

26 May 2023 in Metallurgist
Verified
Journal Article
Closed access
PDF file
LGLeonid Moiseevich Gurevich
Leonid Moiseevich Gurevich
DPDmitry Vladimirovich Pronichev
Dmitry Vladimirovich Pronichev
VKV. P. Kulevich
V. P. Kulevich
OSOleg Slautin
Oleg Slautin
VNV. A. Naumenko
V. A. Naumenko
VKValentin Kharlamov
Valentin Kharlamov