The corrosion behaviour of coated stainless steel as bipolar plate material in PEM fuel cell applications and its improvement through the surface modifications was investigated. A commercial SS316L stainless steel grade was deposited with thin multi-layer coatings, consisting of a carbon top layer and a chromium interlayer of two different thicknesses. Interfacial contact resistance measurements revealed that the applied Cr/C coatings are highly conductive and surpass the ICR criteria, suggested by the U.S. Department of Energy. Corrosion resistance was thoroughly analysed by potentiodynamic polarisation and cyclic voltammetry in 0.5 M $${\hbox {H}_2{\text{SO}}_4}$$ at room temperature and 80 °C, respectively, combined with numerical modelling. Electrochemical results agree well with numerical modelling, including the dissolution of metallic species, local pH-shifts and changes of electrolyte conductivity. Furthermore, the study shows that the application of a Cr/C coating significantly reduces the current density in the passive region during potentiodynamic polarisation and lowering the corrosion rate of the steel substrate by at least a factor of two. Graphical
27 October 2023 in ACS Applied Materials & Interfaces
In this work, the potential of magnetron sputtering, as well as cathodic arc evaporation, is investigated with regard to its suitability as a bipolar plate coating of a PEM fuel cell. For this purpose, Cr and Ti thin films were deposited onto a 0.1 mm SS316L by varying the power and bias voltage. The surface structure and thickness of the coatings are examined via SEM and tactile profilometry. Moreover, the coating variants are compared with each other based on the electrical and electrochemical properties relevant to bipolar plates. The sputtered Cr thin films achieve the lowest contact resistance values and exhibit a columnar structure with a smooth surface. Regarding the electrochemical properties, titanium deposited via cathodic arc evaporation has a low current density in the passive region and high breakthrough potential. All in all, both deposition techniques have their individual advantages for the preparation of bipolar plates’ coatings. However, Ti thin films prepared via cathodic arc seem to be the most suitable option due to the combination of a high deposition rate, a low cost and good coating properties.
Aluminum nitride (AlN) is a promising piezoelectric material for surface acoustic wave (SAW) devices due to its high acoustic velocity and thermal stability. Achieving high-performance SAW devices requires highly c-axis-oriented, columnar AlN thin films with low surface roughness and high Young’s modulus. In this work, [002]-oriented AlN thin films were deposited by radiofrequency sputtering using a ceramic AlN target. Key deposition parameters, including substrate temperature, chamber pressure, and gas composition, were optimized to enhance film quality. Characterization via atomic force microscopy, x-ray diffraction, and scanning electron microscopy confirmed the films’ low surface roughness (0.71 nm), columnar structure with c-axis orientation, and strong crystallinity. The films exhibited a high Young’s modulus of up to 325 GPa. Optimized AlN layers were used to fabricate SAW devices, whose performance was strongly influenced by the AlN thickness and the geometry of the interdigital transducer, including electrode number and device aperture.
In this study, three carbon-based coating variants were deposited onto stainless steel substrates, and the process pressure during the carbon layer deposition was varied. We conducted Raman spectroscopy, transmission electron microscopy, interfacial contact resistance measurements, and potentiodynamic polarization tests to examine the effect of the process pressure on the properties of the coatings. The structural characterization revealed that all specimens exhibit a highly sp2-bonded structure. However, some structural differences could also be identified. In the TEM cross-section images of the carbon layer variants, these structural differences could be observed. The carbon layer deposited at 0.98 Pa has some distortions in the mainly perpendicular graphitic structure, which agrees with the Raman results. Almost completely vertically oriented graphitic layers exhibit the 0.1 Pa coating variant with a d-spacing similar to pure graphite. Regarding the contact resistance, the process pressure has only minor influence. All coatings variants have very low resistance values below 3 m cm2, even at a compaction force of 50 N cm−2, which can be attributed to the graphite-like structure. The polarization tests show that the corrosion resistance increases with increasing process pressure. The best coating variant has a corrosion current density of approximately 10 A cm−2 and almost 10 A cm−2 at room temperature and 80 C, respectively.