With the advent of the data era, most power secondary side equipment tends to be digitized. The power system needs more accurate numerical results to further improve its operating efficiency. Therefore, it is important to study the electromagnetic interferences of very fast transient overvoltage (VFTO) generated by gas-insulated switchgear (GIS). To protect the secondary side cable from interferences, the secondary side cable is wrapped with an outer shield and the shield is grounded. When the interference of VFTO comes, it will couple the interference current and interference voltage on the shield of the cable. By grounding, the interference is greatly discharged. However, due to the grounding resistance, there will be a potential difference between the grounding points at the two ends of the shield of the cable. This causes a corresponding interference current to flow through the shield, which will affect the transmission of signals inside the cable. In the actual substation, the resistivity of the soil, the ambient temperature and humidity of the area, and so on will have impacts on the grounding resistance. In addition, the irregularity of the cable arrangement and the time of the use of the cable will have impacts on the signal transmission of the cable. Based on the abovementioned issues, this article proposed a comprehensive assessment method based on the combination of the cloud model and measurement of alternatives and ranking according to compromise solution (MARCOS). The method brings the cloud model into MARCOS by the algorithm of the contribution of the cloud droplets. It overcomes the difficulty of cloud model quantification. By comparing the results of the proposed method with the actual conditions at the substation and the results of the common MARCOS assessment method, the validity of the method is verified, and a reference scheme is provided for substation optimization.
2 April 2025 in IEEE Transactions on Instrumentation and Measurement
To suppress interference peaks in the low-frequency range of switch-mode power supplies (SMPSs), passive electromagnetic interference (EMI) filters typically require the use of common-mode inductors with higher inductance values. This results in an increase in the volume and weight of SMPSs, as well as a decrease in their efficiency. Therefore, this paper proposes a method for modeling and measurement of conducted EMI suppression elements for SMPSs based on the inverse piezoelectric effect. When piezoelectric ceramics undergo the inverse piezoelectric effect, they vibrate in different modes and generate multiple resonances. At the resonance frequencies, piezoelectric ceramics can provide low-impedance propagation paths for conducted EMI, thereby leading to the attenuation of discrete interference peaks. This paper establishes a model between the resonance frequencies and the dimensions under multiple vibration modes of piezoelectric ceramics, based on their equivalent electrical circuits and resonance properties. The established model enables the synergistic design of resonance frequencies for multiple vibration modes by altering the dimensions of piezoelectric ceramics, thereby achieving significant attenuation of interference peaks at multiple specific frequencies in SMPSs. According to the measurement results, under the same EMI standard, using the piezoelectric ceramics to replace the Y-capacitors as a conducted EMI suppression element in the passive EMI filter can reduce the volume of the common-mode inductor by 88% and its weight by 83%, thereby lowering the cost of the SMPS and improving its efficiency.
6 July 2023 in Applied Computational Electromagnetics Society Journal (ACES)
This paper proposes a method for building a high-frequency model of common-mode chokes in the frequency range of 9kHz to 200MHz. The method only needs to measure the common mode and differential mode impedance data of the common mode choke, and then use the differential evolution algorithm to process the impedance data to complete its high-frequency modeling. Comparison with the high-frequency model obtained by using a genetic algorithm shows that the method has high accuracy. After the high frequency modeling of the common mode chokes, the high frequency modeling of the X and Y capacitors is performed using the differential evolution algorithm, and the high frequency model of the EMI filter is obtained by combining it with the established high frequency model of common mode chokes. By comparing the measured and simulated conducted interference noise suppression effect of the EMI filter, the high frequency model of the common mode chokes is verified to suppress the conducted interference, and the effectiveness of the common mode choke high frequency modeling method is determined.
This paper investigates the robust model predictive load frequency control problem for smart grids with wind power under cyber attacks. To accommodate intermittent power generation, the demand response of the system is considered by involving the air conditioning loads in the frequency regulation. In addition, the system uncertainties produced by the air conditioning load users and wind turbines when replacing traditional generator sets are considered. By using the cone complementary linearization algorithm and the linear matrix inequality technique, a resilience robust model predictive control strategy with mixed performance indexes is proposed. Furthermore, a rigorous derivation of the recursive feasibility of robust model predictive control is given. Finally, the simulation results of the two‐area load frequency control scheme show that the proposed model predictive control strategy is capable of realizing the load frequency control of the multi‐area smart grid and is robust to the parameter uncertainties and frequency regulation of the system. The results also show that the proposed model predictive control strategy has some resistance to cyber attacks and external disturbances.
In this paper, a geometric model of multi-core twisted wire is established to analyze the amplitude-frequency and angular-frequency characteristics of crosstalk in electromagnetic compatibility (EMC). The random combination of the cross-section of the multi-core twisted wire is used to accurately simulate the randomness of the actual multi-core twisted wire. The rotation transformation of the cross-section and the random transposition transformation between the conductors and the neural network model are used to obtain the per unit length (p.u.l) parameters at any position. And bring it into the method of chain parameters to find the crosstalk. The results show that the crosstalk amplitude-frequency and angular-frequency characteristics of the different cores of the multi-core twisted wire under the fixed model are very similar. Under the random model, the crosstalk of multi-core twisted wires is very close in the low frequency range, and satisfies a certain envelope value in the high frequency range. Through comparison with full-wave simulation, the reliability of the proposed method is proved.
1 May 2018 in IOP Conference Series: Earth and Environmental Science
To study concrete cracking, a feedback analysis on variations of surface temperature gradient has been conducted for concrete at the intermission stage of layer pouring with a precise model and finite element simulation method combined with in-situ experiments of a dry hot valley dam. This paper presents the results of concrete stresses and their development under real concrete temperature gradient and explores the internal crack mechanism and possible hidden cracks of the concrete. A discussion on effective measures for prevention of such cracking risk, particularly for construction of valley dams in a dry hot season is also given. This work is of practical reference value for construction of concrete structure in dry hot valley.