This study aimed to develop a simple but effective mechanical-to-electrical energy conversion for harvesting hydrokinetic energy based on triboelectric nanogenerator (TENG) technology. Here, a direct-current fluid-flow-based TENG is reported as a potential solution to solve the inconvenience of directly powering electronic devices where direct-current (DC) power is required. The falling of a water droplet (about 1.06 mL) from an elastomeric pipe can generate an open-circuit voltage of ~35 V, short-circuit current of 3.7 µA, and peak power of 57.6 µW by passing through a separated electrode. Notably, the electrical responses have the distinct characteristics of pulsed direct current. The ability to generate DC outputs enables the TENG to directly drive electronic devices. Our experimental results prove that this TENG can act as a power source to directly light up 50 light-emitting diodes without requiring a rectifier, and, also, the produced electric energy was demonstrated that can be stored directly in a capacitor to power commercial temperature and humidity IoT sensors. Furthermore, the device shows a greatly varied output voltage based on the droplet flow rate, with a linearity R² = 0.998. This work highlights a promising potential for applications in harvesting hydrokinetic energy and self-powered sensors and systems.

Nowadays, hydraulic excavators are an indispensable part of the construction industry; however, conventional hydraulic excavators consume a great deal of fossil fuel and release a large amount of pollution emissions into the environment. This causes many unwanted costs, therefore, effective solutions are required to solve the above-mentioned problems. In this paper, a new independent metering system is proposed to improve energy-saving and reduce costs of a conventional system. In detail, a directional valve is used to control movement and three electro-hydraulic poppet valves are integrated to adjust the flow rate at the inlet and outlet ports of the boom cylinder. In addition, a control strategy based on the coordination between the speed of the pump and the opening area of the spool valve is designed to improve the performance of the system. Specifically, the valves are controlled based on the strategy that the meter-in valve is opened fully to reduce throttling losses and that the meter-out valve is controlled to reduce leakage. The speed of the pump is adjusted according to the feedback position signal. To demonstrate the effectiveness of the new configuration, a real test bench of the boom system was built under laboratory conditions. From the experimental results, the new independent metering valve system not only works with a high tracking precision, but it also reduces energy consumption. Compared with a conventional independent metering system, the fuel economy of the proposed structure can achieve a reduction of approximately 6.5%.

Inspired by improving the adaptive capability of the robot to external impacts or shocks, the adjustable stiffness behavior in joints is investigated to ensure conformity with the safety index. This paper proposes a new soft actuation unit, namely Adjustable Stiffness Rotary Actuator (ASRA), induced by a novel optimization of the elastic energy in an adjusting stiffness mechanism. Specifically, a stiffness transmission is configured by three pairs of antagonistically linear springs with linkage bars. The rotational disk and link bars assist the simplified stiffness control based on a linear transmission. To enhance the elastic energy efficiency, the force compressions of the linear springs are set to be perpendicular to the three-spoke output element, i.e., the output link direction. Besides, the ASRA model is also formed to investigate the theoretical capabilities of the stiffness output and passive energy. As a simulated result, a high passive energy storage ability can be achieved. Then, several experimental scenarios are performed with integral sliding mode controllers to verify the physical characteristics of the ASRA. As trial results, the fast transient response and high accuracy of both the position and stiffness tracking tests are expressed, in turn, independent and simultaneous control cases. Moreover, the real output torque is measured to investigate its reflecting stiffness.

The new configuration of independent metering valve (NIMV) system uses three proportional valves that gave been effectively proven to be energy saving compared with a conventional independent metering valve system in the fixed load condition. However, the variable load condition completely affects the accuracy and energy consumption during the operation of excavators. To improve the motion tracking precision and reduce the energy consumption of the NIMV system, a novel control method based on the coordinated control of the pump and the valve is proposed. In detail, the valve is controlled by considering velocity, load force, and position feedback of the cylinder. Meanwhile, velocity feedforward and position feedback methods are used to control the speed of the pump. In addition, a switching mode for the NIMV system is designed to flexibly select the metering modes based on the load and velocity conditions. To confirm the effectiveness of the proposed control method, the co-simulation model is built by using the AMESim and MATLAB software. From the results, the proposed method not only has high trajectory tracking precision with the displacement error of the cylinder at around 3.6% but also achieves up to 6.4% energy saving.