When an impact drive mechanism (IDM) is subjected to a heavy load, the large inertia of that load will seriously decrease the moving efficiency of the IDM. To solve this problem, a method of dynamic mass isolation is introduced in this study. The influence of load inertia is decreased to a minute value by adopting a light slider and using a spring between the load and the IDM. Thus, the moving efficiency can be increased. Kinematic models have been established and calculated by MATLAB/Simulink. Two prototypes have been fabricated and used to conduct a series of experiments. With a load of 1.8 g, the prototype with dynamic mass isolation presents a moving efficiency of 50.6%, whereas the other prototype without isolation presents a moving efficiency of only 11.9%. As a result, the average step size of the former is approximately four times larger than that of the latter. Moreover, the prototype with dynamic mass isolation can hold almost the same average step size with a wide range of load mass. The proposed method is low cost and may have practical significance for application in any known IDM-based actuating system to improve the performance.
A resonant-type inertial impact linear piezoelectric motor based on coupling of driving and clamping parts was designed and manufactured. The motor mainly includes stator (coupling of driving and clamping parts), mover (slider) and auxiliary parts. The driving part works in the resonant state under the excitation of single harmonic, which mainly realizes the function of reciprocating driving. Similarly, under the single harmonic driving, the clamping part also works in the resonant state to realize the clamping function. Through the coupling between the two parts of the stator, the mover is driven to move continuously in one direction. The inertial impact piezoelectric motor works in the resonant state because the driving and clamping parts work in the resonant state respectively. Compared with the traditional quasi-static inertial impact motor, this study novelly changes the working state of the inertial impact motor. Through the finite element simulation software COMSOL 5.2 , the resonant frequency coupling of the driving and the clamping part is consistent. An experimental platform was built to verify the feasibility of the principle by testing the motor prototype. The experiment results show that: The maximum speed reaches 78 mm s −1 when the motor prototype is operated at the frequency of 810 Hz with a preload of 2 N and the working voltages of clamping and driving parts of motor were set at 80 and 220 V p-p respectively. Meanwhile, the maximum load of the motor prototype can reach 5 N. The minimum resolution of the motor prototype is 6.379 μ m.
A resonant inertial impact rotary piezoelectric motor based on a self-clamping structure is designed, assembled, and tested. The designed piezoelectric motor mainly includes a rotor (two vibrators, preload mechanism, and intermediate connection mechanism), a clamping mechanism, and another auxiliary mechanism. The piezoelectric ceramic sheet on the rotor drives the vibrator to swing under the excitation of a single harmonic wave. Because there is a clamping mechanism formed by the combination of clamp baffle and fixed clamp ring, thus the half-cycle resonant rotation of the rotor can be effectively completed, and repeated harmonic excitation can realize the unidirectional continuous rotation and swing of the rotor. The whole excitation process of the motor is in a resonance state, which has significant advantages, such as low friction and simple structure, compared with the traditional quasi-static piezoelectric motor. The structure of the piezoelectric motor is designed and analyzed using COMSOL5.5 software and then the motor performance is tested and analyzed by building an experimental platform to verify the feasibility of the motor design. The final experimental results show that the optimal working frequency of the piezoelectric motor is 150 Hz, which is consistent with the characteristic frequency of the simulation. When the motor prototype is under the conditions of optimal operating frequency 150 Hz, voltage 240 Vp-p, and preload torque 7.8 N.mm, the maximum angular speed can reach 2.4 rad/s, the maximum load can reach 27.8 N mm and the maximum resolution of the movement angle can reach 0.941°.
9 April 2024 in IEEE Transactions on Industrial Electronics
Traditional inertial impact piezoelectric motors can only operate under quasi-static conditions, resulting in low output force, torque, and speed, and there is a backsliding distance at each cycle that affects their working stability. Recently, many research works have changed their quasi-static working state to a resonance state. In this study, a novel inertial impact piezoelectric motor is proposed. The multimodal and multifrequency band driving method can enable the driver to achieve bidirectional driving and wide resolution adjustment only using a single vibrator, and the unique self-clamping mechanism can effectively suppress the backsliding phenomenon. The dynamics model and FEM model are used for dynamic analysis and modal analysis of the proposed actuator. Manufacturing a prototype and building a test bench to test the performance of the motor. The experimental results show that in the resonant state, the maximum forward output speed is 4.401 mm/s and the displacement resolution is 66 μ m in first-order vibration mode. The maximum reverse output speed is 5.369 mm/s and the displacement resolution is 12 μ m in second-order vibration mode. Meanwhile, the maximum load capacity of the motor is 180 g. Under quasi-static conditions, the minimum displacement resolution of the motor can reach 4 μ m. Under 1 N preload, the backslidings of forward and reverse motor operation are 7.83% and 2.89%, respectively. Under 2 N preload, they are 3.98% and 1.53%, respectively. When the preload exceeds 3 N, the motor does not experience any rebound phenomenon in any state.
An inertial impact rotary piezoelectric motor with non-reversing properties and a clamping mechanism was designed, assembled, and tested. The clamping mechanism can achieve non-reversing motion within the motion cycle, which increases the stability of the motor output. Meanwhile, reversing the direction of the clamping mechanism can realize reverse motion. The dynamic model was simulated using MATLAB/Simulink. A motor prototype was fabricated, and an experimental platform was developed to test the motor performance. Experimental results show that the reverse motion of the mover is considerably suppressed, and its stepping characteristics are excellent. The maximum speed of the motor prototype is 513 mrad s−1, the resolution is 0.834 mrad, and the maximum torque is 42.4 N·mm.