Doga Doǧa

Mr. Doga Doǧa

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 May 2020 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
HPHakan Polat
Hakan Polat
NTNail Tosun
Nail Tosun
DDDoga Doǧa
Doga Doǧa
Ozan KeysanOzan Keysan
Ozan Keysan
A rail geometry with a convex cross section instead of a rectangular one provides a higher contact area, uniform current density, and less transition on the contact surface, and it increases the performance in electromagnetic launchers. In addition, the design of convex rails should be considered together with armature structure, the distance between rails, rail length, and parasitic masses that all have an influence on the overall efficiency and armature/rail transition. A novel complete rail and launch package optimization method is presented in this article. In the first part of this article, the optimum convex rail cross sections for five different separation values are found to obtain uniform current density distribution on rail cross section. For this part, a transient finite element (FE) model in 2-D is developed to calculate the current density distribution and combined with a real-coded genetic algorithm (GA). Then, the armature and sabot petal masses are calculated for each optimized rail geometry and each separation values. In the second part, the efficiency of each optimum design with different separation values is evaluated by a transient 3-D FE model with transient solver taking the calculated armature and sabot petal masses into account. Finally, the length of the rails of the final design is investigated for the transition phenomena. It is observed that 48-mm rail separation with 12.9- and 21-mm elliptical cross-sectional parameters has the highest exit velocity (2355 m/s) for 400-g projectile with uniform current density at inner rail surfaces.

31 May 2019 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
DDDoga Doǧa
Doga Doǧa
MKMustafa Karagoz
Mustafa Karagoz
YCYasin Cevik
Yasin Cevik
BYBaran Yildirim
Baran Yildirim
HPHakan Polat
Hakan Polat
Ozan KeysanOzan Keysan
Ozan Keysan
ASELSAN Inc. has been conducting experimental research on electromagnetic launch technologies since 2014. The first prototype, EMFY-1, has 25 mm x 25 mm square bore and 3-m-length rails. In addition, two capacitor-based pulsed-power supplies (PPSs) with 1- and 4-MJ stored energy are built to supply launcher. During the design process of EMFY-1, a 3-D finite element (FE) model has been developed to simulate the electromagnetic and mechanical aspects of the railgun. This paper presents the simulation and experimental results of EMFY-1 with C-type aluminum armature. FE model, developed using COMSOL Multiphysics, includes both launcher and the PPS system. In addition to the velocity and position of the armature with respect to time, it is possible to observe the magnetic field, current density distributions and breech voltage using the FE model. In the experiments, pulse currents of the PPS modules, breech, and muzzle voltages are measured. The velocity of the projectile is measured using the B-dot probes. In this paper, two experiments of EMFY-1 will be presented. In the first experiment, the launch package with 42-g total mass is accelerated to 2778 m/s, and in the second experiment, the launch package with 130-g total mass is accelerated to 1560 m/s. The simulation results of the proposed FE model are compared with the experiments. It is observed that there is a good agreement between experimental and simulation results.

27 August 2020 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
NTNail Tosun
Nail Tosun
HPHakan Polat
Hakan Polat
DDDoga Doǧa
Doga Doǧa
MKMustafa Karagoz
Mustafa Karagoz
BYBaran Yildirim
Baran Yildirim
Ozan KeysanOzan Keysan
Ozan Keysan
Although electromagnetic launchers (EMLs) are superior to classical gun-powder-based launchers, they have to withstand extreme electrical and mechanical conditions. Therefore, the optimal design and precise simulations of these devices are crucial. In this article, a new simulation strategy for EMLs is proposed in order to achieve high accuracy and reduced complexity. The inductance and electromotive force (EMF) variations in the transient, which have a considerable influence on the launch process, are modeled using the finite element method (FEM) coupled with electrical circuit simulation. The proposed method has a good agreement with the experimental results of two EMLs (EMFY-1 and EMFY-2), which have 25- and 50-mm square bores and 3-m-length launchers. The study showed that the hybrid model with transient inductance and EMF calculations showed a good agreement with experiments that have 625 kJ-3.241-MJ input energies.

26 March 2021 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
NTNail Tosun
Nail Tosun
DDDoga Doǧa
Doga Doǧa
HPHakan Polat
Hakan Polat
Ozan KeysanOzan Keysan
Ozan Keysan
The analysis of the velocity skin effect (VSE) in electromagnetic launchers (EMLs) requires a 3-D transient finite element method, unlike magnetic skin and proximity effects. However, VSE is dominant at high speeds, and this creates convergence problems when moving or deformed mesh physics is used in a transient FEM in the 3-D analysis. Commercial finite element software cannot solve the electromagnetic aspects of such a high-speed application with a transient solver in 3-D. Although 2-D approximations can be used, such an approximation overestimates VSE resistance due to geometry simplifications. In this study, we proposed a novel quasi-transient 3-D FEM model where the air-armature region's conductivity is varied to emulate the high-speed motion of the armature. Results showed that the 2-D approximation overestimates the VSE resistance by almost 40%. The proposed VSE model has been included in the EML model, and simulation results are compared for experimental results with different EMLs, EMFY-1, and EMFY-2 and showed good agreement.

1 November 2022 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
DDDoga Doǧa
Doga Doǧa
RZReza Zeinali
Reza Zeinali
BDBram Daniels
Bram Daniels
KBKonstantin O. Boynov
Konstantin O. Boynov
ELElena A. Lomonova
Elena A. Lomonova
This paper proposes a method to include the anisotropic hysteresis characteristics of soft-magnetic laminated steels in the magnetic equivalent circuit (MEC) modeling. The loop-based MEC formulation is improved to handle the nonlinearity of the anisotropic magnetic hysteresis, including the dynamic classical eddy-current and excess fields. The developed MEC model is coupled with both the single-valued $B$ - $H$ curve (SVC) in magnetostatic and the dynamic vector hysteresis model (VHM) in transient analysis. Results with a single elementary MEC element show that an alternating magnetic field in a single direction with a peak value smaller than 300 A/m causes a discrepancy of more than 10% between the magnetic flux densities calculated by the VHM and SVC at 50 and 200 Hz excitation frequencies. Moreover, the proposed modeling technique is verified experimentally using the laminated transformer core of TEAM problem 32. The induced voltage calculated by the MEC model with the VHM demonstrates a good agreement with the measurements, while the MEC model with the SVC calculates inaccurate voltage waveforms. Lastly, the total iron loss dissipated in the transformer's iron core is investigated to verify the proposed technique under different excitation levels and frequencies up to 500 Hz. It is observed that the proposed MEC model with the vector hysteresis characteristics of laminated steels is able to calculate the iron loss accurately, while the conventional single-valued curve method fails to estimate the iron loss.

7 August 2020 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
DDDoga Doǧa
Doga Doǧa
Léo FriedrichLéo Friedrich
Léo Friedrich
KBK. O. Boynov
K. O. Boynov
ELE. A. Lomonova
E. A. Lomonova
This paper presents a method for the computation of the incremental inductances in a 12/10 variable flux reluctance machine using the hybrid analytical modeling coupled with a fixed-point nonlinear solver. The variation of incremental and apparent inductance with respect to the dc-field excitation is investigated for both zero and non-zero ac-field excitations. The results show that the difference between both inductance values is not negligible after 25 A/mm2 dc-current density for the investigated benchmark without the ac field. Moreover, when a non-zero ac field is introduced in addition to the dc-field, the apparent inductance becomes misleading not only under magnetic saturation but also under low excitation in the linear region of the saturation curve. The results obtained with the proposed nonlinear hybrid model are compared with the finite element method in terms of magnetic flux density distribution and incremental inductance value. The root-mean-square discrepancy of magnetic flux density distribution is found to be 37.6 mT. Furthermore, the discrepancy between incremental inductance results of the proposed method and the finite element model is calculated as 1.43%, while the proposed approach requires less post-processing and necessitates ten times less number of degrees-of-freedom.