1 June 2015 in IEEE Transactions on Magnetics
High-speed permanent magnet machines, supplied by pulsewidth modulation (PWM) voltage source inverters, operate with distorted stator currents. Harmonics present in these stator currents deteriorate the machine performance by generating losses. Mostly, these losses are following the machine design using a transient finite-element model. The precise measurement of these rotor eddy-current losses is extremely difficult, hence, only a few papers provide convincing comparisons between predictions and measurements. This paper presents a fast and precise analytical approach, verified with measurements, to consider rotor losses of machines, supplied by PWM voltages, already during the design procedure.
1 November 2022 in IEEE Transactions on Industry Applications
This paper proposes a method to include the anisotropic hysteresis characteristics of soft-magnetic laminated steels in the magnetic equivalent circuit (MEC) modeling. The loop-based MEC formulation is improved to handle the nonlinearity of the anisotropic magnetic hysteresis, including the dynamic classical eddy-current and excess fields. The developed MEC model is coupled with both the single-valued $B$ - $H$ curve (SVC) in magnetostatic and the dynamic vector hysteresis model (VHM) in transient analysis. Results with a single elementary MEC element show that an alternating magnetic field in a single direction with a peak value smaller than 300 A/m causes a discrepancy of more than 10% between the magnetic flux densities calculated by the VHM and SVC at 50 and 200 Hz excitation frequencies. Moreover, the proposed modeling technique is verified experimentally using the laminated transformer core of TEAM problem 32. The induced voltage calculated by the MEC model with the VHM demonstrates a good agreement with the measurements, while the MEC model with the SVC calculates inaccurate voltage waveforms. Lastly, the total iron loss dissipated in the transformer's iron core is investigated to verify the proposed technique under different excitation levels and frequencies up to 500 Hz. It is observed that the proposed MEC model with the vector hysteresis characteristics of laminated steels is able to calculate the iron loss accurately, while the conventional single-valued curve method fails to estimate the iron loss.
7 August 2020 in IEEE Transactions on Magnetics
This paper presents a method for the computation of the incremental inductances in a 12/10 variable flux reluctance machine using the hybrid analytical modeling coupled with a fixed-point nonlinear solver. The variation of incremental and apparent inductance with respect to the dc-field excitation is investigated for both zero and non-zero ac-field excitations. The results show that the difference between both inductance values is not negligible after 25 A/mm2 dc-current density for the investigated benchmark without the ac field. Moreover, when a non-zero ac field is introduced in addition to the dc-field, the apparent inductance becomes misleading not only under magnetic saturation but also under low excitation in the linear region of the saturation curve. The results obtained with the proposed nonlinear hybrid model are compared with the finite element method in terms of magnetic flux density distribution and incremental inductance value. The root-mean-square discrepancy of magnetic flux density distribution is found to be 37.6 mT. Furthermore, the discrepancy between incremental inductance results of the proposed method and the finite element model is calculated as 1.43%, while the proposed approach requires less post-processing and necessitates ten times less number of degrees-of-freedom.
22 May 2015 in IEEE Transactions on Magnetics
A widely used method for the magnetic field calculation in permanent magnet (PM) machines is the harmonic modeling (HM) method. Despite its many advantages, the application of this method is limited to machines in which armature currents, as a source of the magnetic field, are known. Since most of the PM machines are supplied with three-phase voltages, any variation of parameters in the armature electric circuit could lead to the uncertainty in knowing the armature currents, and therefore, limit use of the HM method. In this paper, an approach for overcoming this limitation is presented, which enables the calculation of the magnetic field in the PM machines without a priori knowledge of the armature currents.
29 December 2015 in IEEE Transactions on Magnetics
Helical windings (or zigzag windings) are used in a number of applications, however, in electrical machines, mainly employed in low-power, high-speed permanent magnet (PM) brushless dc machines due to the cost effectiveness of the winding type while maintaining reasonable performance. Typically, helical windings are used for low-voltage applications due to their spiral form, which makes them most suitable for a small number of turns. In high-speed electrical machines, such a low number of turns are applicable. It is apparent that high-speed PM machines suffer from rotor eddy-current losses, which in some cases may lead to PM demagnetization due to overheating. The performance of the machine is compromised by these losses; hence, they have to be considered during the design procedure. There are many papers analyzing the magnetic field of these machines employing helical windings; however, none of them present a simple and precise electromagnetic model of a machine with the helical winding. This paper presents an analytical approach to model the resulting 3-D magnetic field of the helical winding, considering eddy currents in the conducting media of the rotor. The model is verified with the 3-D finite-element method by means of comparing magnetic field and rotor eddy-current losses.