A low-power SAR ADC with capacitor-splitting energy-efficient switching scheme is proposed for wearable biosensor applications. Based on capacitor-splitting, additional reference voltage V_cm, and common-mode techniques, the proposed switching scheme achieves 93.76% less switching energy compared to the conventional scheme with common-mode voltage shift in one LSB. With the switching scheme, the proposed SAR ADC can lower the dependency on the accuracy of V_cm and the complexity of digital control logic and DAC driver circuits. Furthermore, the SAR ADC employs low-noise and low-power dynamic comparators utilizing multi-clock control, low sampling error sampling switches based on the bootstrap technique, and dynamic SAR logic. The simulation results demonstrate that the ADC achieves a 61.77 dB SNDR and a 78.06 dB SFDR and consumes 4.45 μW of power in a 180 nm process with a 1 V power supply, a full-swing input signal frequency of 93.33 kHz, and a sampling rate of 200 kS/s.

A hybrid energy-efficient, area-efficient, low-complexity switching scheme in SAR ADC for biosensor applications is proposed. This scheme is a combination of the monotonic technique, the MSB capacitor-splitting technique, and a new switching method. The MSB capacitor-splitting technique, as well as the reference voltage V_aq allow for more options for reference voltage conversion, resulting in higher area savings and higher energy efficiency. In a capacitor array, the circuit performs unilateral switching during all comparisons except for the second and last two comparisons, reducing the difficulty in designing the drive circuit. The proposed switching scheme saves 98.4% of the switching energy and reduces the number of unit capacitors by 87.5% compared to a conventional scheme. Furthermore, the SAR ADC employs low-noise and low-power dynamic comparators utilizing multi-clock control, low-sampling error-sampling switches based on the bootstrap technique, and dynamic SAR logic. The simulation results demonstrated that the proposed SAR ADC achieves 61.51 dB SNDR, 79.21 dB SFDR and consumes 0.278 μW of power in a 180 nm process with a 1 V power supply, a full swing input signal frequency of 23.33 kHz, and a sampling rate of 100 kS/s.

A twice‐input variable‐resolution single‐side switching scheme without reset energy is proposed for successive approximation register (SAR) analogue‐to‐digital converters (ADCs). The proposed switching scheme is based on semi‐resting DAC technology to design a four‐array architecture capable of handling twice the swing of the signal input while reducing the capacitor array size. The technique of top‐plate sampling and monotonic shift is utilized so that no switching energy is generated for the first three comparisons. The proposed scheme utilizes full‐capacitor split, bridged switch, and C‐2C dummy capacitor technology, which reduces average switching energy consumption by 99.8% compared to conventional schemes and enables ADC variable resolution function, making the SAR ADC more suitable for IoT applications.

A 9-10-bit adjustable and energy-efficient switching scheme for SAR ADC with one-LSB common-mode voltage variation is proposed. Based on capacitor-splitting technology and common-mode conversion techniques, the proposed switching scheme reduces the DAC switching energy by 96.41% compared to the conventional scheme. The low complexity and the one-LSB common-mode voltage offset of this scheme benefit from the simultaneous switching of the reference voltages of the capacitors corresponding to the positive array and the negative array throughout the entire reference voltage switching process, and the reference voltage of each capacitor in the scheme does not change more than two voltages. The post-layout result shows that the ADC achieves the 54.96 dB SNDR, the 61.73 dB SFDR, and the 0.67 μw power consumption with the 10-bit mode and the 48.33 dB SNDR, the 54.17 dB SFDR, and the 0.47 μw power consumption with the 9-bit mode in a 180 nm process with a 100 kS/s sampling frequency.

In recent years, successive approximation register (SAR) analogue‐to‐digital converters (ADCs) have been widely applied in Internet of Things (IoT) sensor devices. To reduce the power consumption of ADCs, a bridged‐switch energy‐efficient switching scheme for SAR ADCs with a 2× input range is proposed. Due to the use of top‐plate sampling, overall shift and bridged switch, the energy consumption of the first three comparisons and reset is zero, meanwhile the energy consumption of the fifth comparison is greatly reduced. The proposed switching scheme has an average energy consumption of 13.084 CV _ref ² , which reduces the switching energy by 99.04% compared to the conventional switching scheme. The proposed switching scheme can achieve a 2× input range with the same supply voltage, effectively reducing ADC power consumption and making it more suitable for IoT applications.