In a cut-in scenario, traditional adaptive cruise control usually cannot effectively identify the cut-in vehicle and respond to it in advance. This paper proposes an adaptive cruise control (ACC) strategy based on the MPC algorithm for cut-in scenarios. A finite state machine (FSM) is designed to manage vehicle control in different cut-in scenarios. For a cut-in scenario, a method to identify and quantify the possibility of cut-in of a vehicle is proposed. At the same time, a safety distance model of the cut-in vehicle is established as the basis for the state transition of the finite state machine. Taking the quantified cut-in possibility of a vehicle as a reference, the model predictive control (MPC) algorithm, which considers the constraints of driving safety and comfort, is used to realize coordinated control of the host vehicle and the cut-in vehicle. Simulink–Carsim simulation studies show that the ACC strategy for a cut-in scenario can effectively identify a cut-in vehicle and quantify the possibility of cut-in of the vehicle. Faced with a cut-in vehicle, the host vehicle using the ACC strategy can brake several seconds early and switch the following target to the cut-in vehicle. Meanwhile, the acceleration and jerk of the host vehicle changes within a reasonable range, which ensures driving safety and comfort.

Automatic emergency braking systems (AEBS) significantly improve the active safety performance of commercial vehicles, but their effectiveness is affected by the vehicle’s driving conditions, which mainly include the vehicle load and road conditions. In order to improve the adaptability of the AEBS, an AEBS control strategy with adaptive driving conditions was proposed and validated using a simulation and experimentation. This AEBS control strategy was designed based on an estimation of the vehicle mass, the center of gravity position, road grade, and the tire-road friction coefficient. In the simulation and experimental verification, the braking deceleration and braking distance under different driving conditions were compared. The results show that the AEBS control strategy proposed in this paper can avoid collisions in all test scenarios and maintain a parking spacing of approximately 5 m. In an extreme test scenario with a full load and low tire–road friction, as compared with the fixed threshold control strategy, the warning can be issued 0.2 s earlier and the maximum intensity braking can be carried out 0.5 s earlier.

With the development of electric vehicles (EVs), accurate prediction of the remaining driving range (RDR) is a crucial issue. However, predicting RDR for EVs still poses significant challenges, particularly under complex traffic scenarios and personalized driving behaviors, where existing methodologies struggle to meet adaptability requirements. This study proposes a novel RDR prediction method for EVs that incorporates personalized driving behavior and emphasizes the influence of future route information on prediction performance. Real-world driving data, encompassing driving patterns, traffic conditions, and road characteristics, serve as the foundation for constructing a precise driving behavior model with Hidden Markov Model (HMM) and Fuzzy Markov Model (FMM). Furthermore, an energy consumption model that integrates the physical model with machine learning techniques is constructed to accurately predict energy consumption rates under future driving cycles. By coupling this consumption rate with battery load in an equivalent circuit model (ECM), the RDR is accurately predicted. To validate the performance of the proposed method, it is compared with baseline models under various driving scenarios. Experimental results demonstrate the accuracy and adaptability of the model, with a relative error within 10% in practical driving validation. This methodology offers insights into energy efficiency optimization and intelligent decision-making for EVs in complex traffic environments.

Under the trend of vehicle intelligentization, many electrical control functions and control methods have been proposed to improve vehicle comfort and safety, among which the Adaptive Cruise Control (ACC) system is a typical example. However, the tracking performance, comfort and control robustness of the ACC system need more attention under uncertain environments and changing motion states. Therefore, this paper proposes a hierarchical control strategy, including a dynamic normal wheel load observer, a Fuzzy Model Predictive Controller and an integral-separate PID executive layer controller. Firstly, a deep learning-based dynamic normal wheel load observer is added to the perception layer of the conventional ACC system and the observer output is used as a prerequisite for brake torque allocation. Secondly, a Fuzzy Model Predictive Control (fuzzy-MPC) method is adopted in the ACC system controller design, which establishes performance indicators, including tracking performance and comfort, as objective functions, dynamically adjusts their weights and determines constraint conditions based on safety indicators to adapt to continuously changing driving scenarios. Finally, the executive controller adopts the integral-separate PID method to follow the vehicle’s longitudinal motion commands, thus improving the system’s response speed and execution accuracy. A rule-based ABS control method was also developed to further improve the driving safety of vehicles under different road conditions. The proposed strategy has been simulated and validated in different typical driving scenarios and the results show that the proposed method provides better tracking accuracy and stability than traditional techniques.

Providing safe, smooth, and efficient trajectories for autonomous vehicles has long been a question of great interest in the field of autopiloting. In dynamic and ever-changing urban environments, safe and efficient trajectory planning is fundamental to achieving autonomous driving. Nevertheless, the complexity of environments with multiple constraints poses challenges for trajectory planning. It is possible that behavior planners may not successfully obtain collision-free trajectories in complex urban environments. Herein, this paper introduces spatio–temporal joint optimization-based trajectory planning (SJOTP) with multi-constraints for complex urban environments. The behavior planner generates initial trajectory clusters based on the current state of the vehicle, and a topology-guided hybrid A* algorithm applied to an inflated map is utilized to address the risk of collisions between the initial trajectories and static obstacles. Taking into consideration obstacles, road surface adhesion coefficients, and vehicle dynamics constraints, multi-constraint multi-objective coordinated trajectory planning is conducted, using both differential-flatness vehicle models and point-mass vehicle models. Taking into consideration longitudinal and lateral coupling in trajectory optimization, a spatio–temporal joint optimization solver is used to obtain the optimal trajectory. The simulation verification was conducted on a multi-agent simulation platform. The results demonstrate that this methodology can obtain optimal trajectories safely and efficiently in complex urban environments.

Distributed drive electric vehicles improve steering response and enhance overall vehicle stability by independently controlling each motor. This paper introduces a control framework based on Adaptive Model Predictive Control (AMPC) for coordinating handling stability, consisting of three layers: the dynamic supervision layer, online optimization layer, and low-level control layer. The dynamic supervision layer considers the yaw rate and maneuverability limits when establishing the $\beta -\dot{\beta }$ phase plane stability boundary and designs variable weight factors based on this stability boundary. The online optimization layer constructs the target weight-adaptive AMPC strategy, which can adjust the control weights for maneuverability and lateral stability in real time based on the variable weight factors provided by the dynamic supervision layer. The low-level control layer precisely allocates the driver’s requested driving force and additional yaw moment by using torque distribution error and tire utilization as the cost function. Finally, experiments are conducted on a Simulink-CarSim co-simulation platform to assess the performance of AMPC. Simulation results show that, compared to the traditional MPC strategy, this control strategy not only enhances maneuverability under normal conditions but also improves lateral stability control under extreme conditions.