Micro-light-emitting diode displays are generating considerable interest as a promising technology for augmented-reality glasses. However, the fabrication of highly efficient and ultra-small ( <3 μm) micro-light-emitting diodes, which are required for augmented-reality applications, remains a major technical challenge due to the presence of strong sidewall nonradiative recombination. In this study, we demonstrate a 3.5 × 3.5 μm2 blue GaN micro-light-emitting diode with negligible sidewall nonradiative recombination compared with bulk nonradiative recombination. We achieve this by using an ultralow-damage dry etching technique, known as neutral beam etching, to create the micro-light-emitting diode mesa. Our 3.5 × 3.5 μm2 micro-light-emitting diode exhibits a low decrease in external quantum efficiency of only 26% at a current density of 0.01 A/cm2, compared with the maximum external quantum efficiency that is reached at the current density of ∼3 A/cm2. Our findings represent a significant step towards realizing micro-light-emitting diode displays for augmented-reality glasses.
28 May 2020 in Semiconductor Science and Technology
A nanodisk array of blue InGaN/GaN multiple quantum wells was made using neutral beam etching (NBE) followed by GaN regrowth. The NBE-fabricated nanodisk presented a vertical and highly smooth sidewall surface where the InGaN well layers were easily distinguished even with a scanning electron microscope. A high interface quality without any voids or obvious defects was obtained between the nanodisk and the regrown-GaN layer. The nanodisk after regrowth presented a smaller blueshift of photoluminescence emission energy (12 meV) and a substantially higher and almost constant internal quantum efficiency of ∼50% over three orders of magnitude of excitation laser power when compared to the nanodisk before regrowth. This study shows that the process of NBE nanodisk etching followed by GaN regrowth represents a promising step forward in the development of truncated cone-shaped directional micro-LEDs with a buried active region in a top-down structure.
Commercially available formulations of the popular conductive polymer, poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) are aqueous dispersions that require the addition of secondary dopants such as dimethyl sulphoxide (DMSO) or ethylene glycol (EG) for fabricated films to have the desired levels of conductivity. CleviosTM F HC Solar, a formulation of PEDOT:PSS produced by Heraeus, GmbH, achieves over 500 S/cm without these secondary dopants. This work studies whether secondary dopants such as DMSO have any additional effect on this type of PEDOT:PSS. The temperature dependencies of the conductivity of F HC Solar spin-coated thin films measured using a four-probe method seem to exhibit different charge transport properties compared with secondary doped PH1000. Observations made using atomic force microscopy (AFM) show that different concentrations of DMSO affect the orientation of the PEDOT domains in the thin film. These morphological changes cause room temperature conductivity to reduce from 640 S/cm in pristine films to as low as 555 S/cm after adding 7 wt% of DMSO along the film. Such tuning may prove useful in future applications of PEDOT:PSS, such as nanoprobes, transistors and hybrid solar cells.
17 August 2023 in IEEE Open Journal of Nanotechnology
This study investigated the electrical properties of AlGaN/GaN high-electron-mobility transistors (HEMTs) with varied recess depths under the gate electrode. We demonstrated a recess depth of approximately 6 nm, which was achieved through neutral beam etching (NBE) technique with a low etch rate of 1.8nm/min, resulting in device enhancement-mode (E-mode) behavior with threshold voltage (V th ) of 0.49 V. The effects of post-metallization annealing (PMA) on the device performance were also examined. The results revealed that PMA treatment improves the DC characteristics of the devices, including maximum drain current (I DMAX ), transconductance (g m ), subthreshold swing (SS), on-off ratio, and off-state leakage current, with maximum enhancement percentage of 18.3% for IDMAX, 3758% for on-off ratio, and 54.3% for SS. Moreover, this study compared the recess depths of metal-insulator-semiconductor high-electron-mobility transistors (MIS-HEMTs) with the SiN dielectric layer. The results showed that MIS-HEMTs exhibit more negative V th values, which can be attributed to the controlled surface states achieved through passivation.
14 April 2020 in Journal of Vacuum Science & Technology A
In the gate-recess formation process, normally-off operation is achieved by removing the barrier layer by dry etching to reduce the two-dimensional-electron-gas concentration under the gate electrode. An atomic-layer defect-free etching of GaN is thus indispensable to achieve high-frequency, high-power, and normally-off operation. More-precise atomic-layer defect-free GaN etching was investigated by using an HBr neutral beam. This investigation found that the HBr neutral beam could achieve more-precise atomic-layer etching than the Cl2 neutral beam because the HBr chemistry can control the reactivity of atomic-layer etching by forming a thinner and less-volatile reaction layer.
3 February 2022 in Journal of Vacuum Science & Technology A
This study reports the fabrication of the high-quality hafnium dioxide (HfO2) film at room temperature (20–30 °C) using the neutral beam enhanced atomic layer deposition (NBEALD) we developed. The HfO2 film was fabricated using tetrakis(ethylmethylamino)hafnium (TEMAH) as the Hf precursor and O2 NB as the oxidant. Argon gas was used for the carrier and purge gases. The HfO2 film-deposition process consists of 5-s TEMAH feed, 5-s Ar purge, 5-s O2 gas injection, 20-s O2 neutral beam irradiation, and 5-s Ar purge. The HfO2 film exhibited a saturated growth per cycle of 0.18 nm/cycle and a high-quality film with low C contamination (2.7%), N contamination (3.9%), and a good O/Hf ratio (2.0) was achieved. The film also had an ideal refractive index of 1.9. Additionally, continuously grown high-quality HfO2 and silicon dioxide (SiO2) gate oxide films (stacked HfO2/SiO2 gate oxide film) were successfully fabricated at room temperature. This film has the potential to decrease the thermal budget, thus enabling high flexibility when designing semiconductor structures. These findings demonstrate the effectiveness of our NBEALD in forming high-k gate stack structures.