Shuainan Liu

Mr. Shuainan Liu


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 February 2024 in Coatings
Verified
Journal Article
Open access
PDF file
ZTZhongxiang Tang
Zhongxiang Tang
TYTing Yang
Ting Yang
CZChengcheng Zhang
Chengcheng Zhang
WWWeize WANG
Weize WANG
SLShuainan Liu
Shuainan Liu
CLChen Liu
Chen Liu
The development of gas turbine technology has led to an increase in the complexity of the geometric shape of the sprayed workpiece. Consequently, it has become more difficult to maintain the perpendicularity of the spraying angle during the spraying process, thereby impacting the structure and performance of the coating. This study uses the atmospheric plasma spraying method to simultaneously spray two types of powder for the preparation of embedded micro-agglomerated particle (EMAP) coatings. The spraying process is conducted at four different angles, ranging from 90° to 30°, in order to analyze the influence of the spray angle on the particle deposition and coating performance. The experimental results demonstrate that the relative deposition efficiency, hardness, and elastic modulus of the EMAP coatings decreased as the spray angle decreased. The porosity exhibited a reduction when the spraying angle dropped from 90° to 50°, followed by a significant rise at 30°. The greatest relative amount of second phase particles embedded in the coating appeared at a spraying angle of 90°, amounting to 10.8%. The smallest amount was found at a spraying angle of 30°, with a relative quantity of 2.2%. Furthermore, the molten droplets of the first phase matrix powder underwent extension and fragmentation along the angular direction at low angles. At an angle of 90°, the maximum average thermal shock life was 40.6 cycles, with the best stability of thermal shock life. The decrease in the spraying angle resulted in a deterioration in both the thermal shock life and its stability.

31 August 2023 in Coatings
Verified
Journal Article
Open access
PDF file
CLChen Liu
Chen Liu
WWWeize WANG
Weize WANG
TYTing Yang
Ting Yang
YLYangguang Liu
Yangguang Liu
ZTZhongxiang Tang
Zhongxiang Tang
SLShuainan Liu
Shuainan Liu
With the development of the aerospace industry, the close exploration of the Sun has become a human demand. However, close-range exploration means that the detection satellite needs to accept the test of high temperatures above 1400 °C, so a thermal protective coating is a necessary part of the detection satellite to isolate heat and reflected light. Al2O3 coating has the characteristics of high emissivity and low absorptivity, and it is the best choice for thermal protection coating. However, the coating is subjected to thermal cycles, including heating and cooling, as the satellite rotates around the Sun, which could result in a change in the structure and properties of the coating. Therefore, thermal shock experiments were carried out, and the influence of microstructure on the absorption rate of the Al2O3 coating was investigated. In this study, an Al2O3 coating was prepared by atmospheric plasma spraying (APS). The coating was subjected to a thermal shock (TS) test at 1400 °C using a self-made flame shock device, and coating samples under different thermal shock degrees were obtained. A scanning electron microscope (SEM) was used to characterize the coating pores, and the effects of the coating pore size, aspect ratio (A/R) and cracks in the coating on the optical properties of the coating under different thermal shock degrees were analyzed. In order to clarify the influence of coating microstructure changes on the optical properties of the coating under different thermal shock degrees, not only relevant experiments were carried out, but also the solar reflectivity of Al2O3 coatings with different pore structures was analyzed by the finite element method using finite-difference time-domain (FDTD). The results show that increasing the porosity and aspect ratio of the pores can improve the partial solar absorption of the coating. It was also found that the transverse crack propagation improves the solar reflectance of the coating.

24 December 2023 in Coatings
Verified
Journal Article
Open access
PDF file
SLShuainan Liu
Shuainan Liu
WWWeize WANG
Weize WANG
TYTing Yang
Ting Yang
YLYangguang Liu
Yangguang Liu
CLChen Liu
Chen Liu
XZXiaoqin Zhang
Xiaoqin Zhang
Residual stress plays an important role in the formation and growth of cracks in thermal barrier coatings and single-crystal superalloy substrates. In this study, a finite element model for a planar double-layer thermal barrier coating and a crystal plasticity finite element model based on dislocation slip-induced plastic deformation of single-crystal materials were established to analyze the residual stress in the coatings and the substrate, considering the creep and crystal plasticity of the substrate materials. The simulation results show that the thermal barrier coatings bear most of the stress generated by high temperatures, and the residual stress of the substrate is small. By comparing the two material properties to calculate the interface stress when the amplitude of the interface between the substrate and the coating is 30 μm and the thickness of the thermal grown oxide layer is 5 µm, the interfacial stress of the substrate at the macro scale was found to be similar to the interfacial stress at the micro slip system scale. Based on the cumulative shear strain, it was determined that the [001]-, [011]-, and [111]-oriented alloys activated the 12, 8, and 4 groups, respectively, under the combined action of thermal stress and centrifugal force of the coating. Comparing the activation of different initial orientation slip systems and the magnitude of the yield stress provides a theoretical foundation to study the structural integrity of single-crystal alloys.