Thermal barrier coatings (TBCs) play a crucial role in enhancing the operating temperature of key equipment. However, when TBCs are sprayed on the internal surface of these components, there are issues related to the imperfect internal diameter atmospheric plasma spray (ID-APS) process and the unsatisfactory performance of TBCs in internal holes. Yttria-stabilized zirconia (YSZ), YSZ + Gadolinium zirconate (GZ) and YSZ + tantalate (RETaO4) TBCs were prepared using the SM F210 ID-APS gun. The thermal shock and particle erosion resistance of the coatings were compared, and the relationship between the structure and properties was investigated. The results show that the hardness, fracture toughness and erosion resistance of the three coatings are the largest in the YSZ coating and the smallest in the GZ coating. YSZ coating also has the best thermal shock resistance. These research findings have important guiding significance for the improvement of the ID-APS process.
In recent years, with the development of SiC composites in aero-engine hot-end components, environmental barrier coatings (EBCs) have received extensive attention. Moreover, in order to elevate the service temperature, it is a developing trend to apply thermal barrier coatings (TBCs) with low thermal conductivity on EBCs coating system to form thermal/environmental barrier coatings (T/EBCs). However, the combination of high coefficient of thermal expansion (CTE) of TBCs with low CTE of EBCs often leads to premature failure due to excessive thermal expansion mismatch stress. However, a novel structural thermal barrier coating with embedded micro-agglomerated particles (EMAP TBC) by using atmospheric plasma spraying (APS) process has brought hope to solve this problem due to its low elastic modulus. Therefore, in this study, an innovative EMAP Gd2Zr2O7 T/EBCs coating system (EMAP Gd2Zr2O7/Yb2Si2O7/Si) under 1500 °C flame thermal shock was simulated and systematically studied on the SiC substrate. The results showed that the EMAP Gd2Zr2O7 T/EBCs coating system has much lower thermal stress than the conventional Gd2Zr2O7/Yb2Si2O7/Si T/EBCs coating system. Furthermore, when the thickness of each layer of the EMAP Gd2Zr2O7 T/EBCs coating system varies, to meet the thermal insulation requirements of Yb2Si2O7 layer and reduce the thermal shock stress, the thickness of the EMAP Gd2Zr2O7 layer is recommend being about 100 μm. Meanwhile, the thicknesses of Yb2Si2O7 and Si layers can be set as large as needed. In addition, with the increase in Yb2SiO5 doping content in the Yb2Si2O7 intermediate layer, the EMAP Gd2Zr2O7 T/EBCs coating system suffers a greater risk of spalling failure due to the increase in thermal stress.
Thermal barrier coatings (TBCs) material has excellent high-temperature resistance and heat insulation performance, which plays a vital role in improving the working efficiency and running life of the engine. During the flight, the engine will inhale dust particles in the air. These particles are mostly from siliceous debris, which are usually called calcium magnesium aluminum silicate (CMAS). At present, CMAS corrosion has become one of the important problems affecting the service life of thermal barrier coatings. In this study, conventional yttrium oxide stabilized zirconia (YSZ) coatings and ytterbium oxide and yttrium oxide co-stabilized zirconia (YbYSZ) coatings were prepared by atmospheric plasma spraying. The two coatings were examined under thermal cycling-CMAS coupling conditions and divided into six life stages. The failure modes, CMAS permeation behavior, crack characteristics and mechanical properties of the two coatings at different life stages were evaluated systematically. The experimental results show that the YbYSZ coating has a longer life than YSZ coating under the thermal cycling and CMAS coupling condition, which increases by about 83% compared with the conventional YSZ coating. In the whole life stage, the porosity of YbYSZ coating is always higher than that of YSZ coating. The phase transition is not the reason for the failure and spalling of the coatings. The crack length of the two coatings showed an increasing trend, but the crack length of the YSZ coating was higher than that of the YbYSZ coating, and the crack density of the two coatings showed a “saddle shape”, which was more obvious for the YSZ coating. The YbYSZ coating shows better mechanical properties under the thermal cycling-CMAS coupling condition with the evolution of life.
With the development of the aerospace industry, the close exploration of the Sun has become a human demand. However, close-range exploration means that the detection satellite needs to accept the test of high temperatures above 1400 °C, so a thermal protective coating is a necessary part of the detection satellite to isolate heat and reflected light. Al2O3 coating has the characteristics of high emissivity and low absorptivity, and it is the best choice for thermal protection coating. However, the coating is subjected to thermal cycles, including heating and cooling, as the satellite rotates around the Sun, which could result in a change in the structure and properties of the coating. Therefore, thermal shock experiments were carried out, and the influence of microstructure on the absorption rate of the Al2O3 coating was investigated. In this study, an Al2O3 coating was prepared by atmospheric plasma spraying (APS). The coating was subjected to a thermal shock (TS) test at 1400 °C using a self-made flame shock device, and coating samples under different thermal shock degrees were obtained. A scanning electron microscope (SEM) was used to characterize the coating pores, and the effects of the coating pore size, aspect ratio (A/R) and cracks in the coating on the optical properties of the coating under different thermal shock degrees were analyzed. In order to clarify the influence of coating microstructure changes on the optical properties of the coating under different thermal shock degrees, not only relevant experiments were carried out, but also the solar reflectivity of Al2O3 coatings with different pore structures was analyzed by the finite element method using finite-difference time-domain (FDTD). The results show that increasing the porosity and aspect ratio of the pores can improve the partial solar absorption of the coating. It was also found that the transverse crack propagation improves the solar reflectance of the coating.
Residual stress plays an important role in the formation and growth of cracks in thermal barrier coatings and single-crystal superalloy substrates. In this study, a finite element model for a planar double-layer thermal barrier coating and a crystal plasticity finite element model based on dislocation slip-induced plastic deformation of single-crystal materials were established to analyze the residual stress in the coatings and the substrate, considering the creep and crystal plasticity of the substrate materials. The simulation results show that the thermal barrier coatings bear most of the stress generated by high temperatures, and the residual stress of the substrate is small. By comparing the two material properties to calculate the interface stress when the amplitude of the interface between the substrate and the coating is 30 μm and the thickness of the thermal grown oxide layer is 5 µm, the interfacial stress of the substrate at the macro scale was found to be similar to the interfacial stress at the micro slip system scale. Based on the cumulative shear strain, it was determined that the [001]-, [011]-, and [111]-oriented alloys activated the 12, 8, and 4 groups, respectively, under the combined action of thermal stress and centrifugal force of the coating. Comparing the activation of different initial orientation slip systems and the magnitude of the yield stress provides a theoretical foundation to study the structural integrity of single-crystal alloys.