We present the architecture and three applications of the largest resolution image sensor based on single-photon avalanche diodes (SPADs) published to date. The sensor, fabricated in a high-voltage CMOS process, has a resolution of 512 × 128 pixels and a pitch of 24 μm. The fill-factor of 5% can be increased to 30% with the use of microlenses. For precise control of the exposure and for time-resolved imaging, we use fast global gating signals to define exposure windows as small as 4 ns. The uniformity of the gate edges location is ∼140 ps (FWHM) over the whole array, while in-pixel digital counting enables frame rates as high as 156 kfps.

We review the advancement of the research toward the design and implementation of quantum plenoptic cameras, radically novel 3D imaging devices that exploit both momentum–position entanglement and photon–number correlations to provide the typical refocusing and ultra-fast, scanning-free, 3D imaging capability of plenoptic devices, along with dramatically enhanced performances, unattainable in standard plenoptic cameras: diffraction-limited resolution, large depth of focus, and ultra-low noise. To further increase the volumetric resolution beyond the Rayleigh diffraction limit, and achieve the quantum limit, we are also developing dedicated protocols based on quantum Fisher information. However, for the quantum advantages of the proposed devices to be effective and appealing to end-users, two main challenges need to be tackled. First, due to the large number of frames required for correlation measurements to provide an acceptable signal-to-noise ratio, quantum plenoptic imaging (QPI) would require, if implemented with commercially available high-resolution cameras, acquisition times ranging from tens of seconds to a few minutes. Second, the elaboration of this large amount of data, in order to retrieve 3D images or refocusing 2D images, requires high-performance and time-consuming computation. To address these challenges, we are developing high-resolution single-photon avalanche photodiode (SPAD) arrays and high-performance low-level programming of ultra-fast electronics, combined with compressive sensing and quantum tomography algorithms, with the aim to reduce both the acquisition and the elaboration time by two orders of magnitude. Routes toward exploitation of the QPI devices will also be discussed.

The paper presents a camera comprising 512 × 128 pixels capable of single-photon detection and gating with a maximum frame rate of 156 kfps. The photon capture is performed through a gated single-photon avalanche diode that generates a digital pulse upon photon detection and through a digital one-bit counter. Gray levels are obtained through multiple counting and accumulation, while time-resolved imaging is achieved through a 4-ns gating window controlled with subnanosecond accuracy by a field-programmable gate array. The sensor, which is equipped with microlenses to enhance its effective fill factor, was electro-optically characterized in terms of sensitivity and uniformity. Several examples of capture of fast events are shown to demonstrate the suitability of the approach.

The LinoSPAD camera system is a modular, compact and versatile time-resolved camera system, combining a linear 256 high fill factor pixel CMOS SPAD (single-photon avalanche diode) sensor with an FPGA (field-programmable gate array) and USB 3.0 transceiver board. This modularization permits the separate optimization or exchange of either the sensor front-end or the processing back-end, depending on the intended application, thus removing the traditional compromise between optimal SPAD technology on the one hand and time-stamping technology on the other hand. The FPGA firmware implements an array of 64 TDCs (time-to-digital converters) with histogram accumulators and a correction module to reduce non-linearities. Each TDC is capable of processing over 80 million photon detections per second and has an average timing resolution better than 50 ps. This article presents a complete and detailed characterization, covering all aspects of the system, from the SPAD array light sensitivity and noise to TDC linearity, from hardware/firmware/software co-design to signal processing, e.g., non-linearity correction, from power consumption to performance non-uniformity.

Fluorescence lifetime imaging microscopy (FLIM) is a powerful imaging technique that enables the visualization of biological samples at the molecular level by measuring the fluorescence decay rate of fluorescent probes. This provides critical information about molecular interactions, environmental changes, and localization within biological systems. However, creating high-resolution lifetime maps using conventional FLIM systems can be challenging, as it often requires extensive scanning that can significantly lengthen acquisition times. This issue is further compounded in three-dimensional (3D) imaging because it demands additional scanning along the depth axis. To tackle this challenge, we developed a computational imaging technique called light-field tomographic FLIM (LIFT-FLIM). Our approach allows for the acquisition of volumetric fluorescence lifetime images in a highly data-efficient manner, significantly reducing the number of scanning steps required compared to conventional point-scanning or line-scanning FLIM imagers. Moreover, LIFT-FLIM enables the measurement of high-dimensional data using low-dimensional detectors, which are typically low cost and feature a higher temporal bandwidth. We demonstrated LIFT-FLIM using a linear single-photon avalanche diode array on various biological systems, showcasing unparalleled single-photon detection sensitivity. Additionally, we expanded the functionality of our method to spectral FLIM and demonstrated its application in high-content multiplexed imaging of lung organoids. LIFT-FLIM has the potential to open up broad avenues in both basic and translational biomedical research.

The Hanbury Brown–Twiss (HBT) effect holds a pivotal place in intensity interferometry and gave a seminal contribution to the development of quantum optics. To observe such an effect, both good spectral and timing resolutions are necessary. Most often, the HBT effect is observed for a single frequency at a time due to its limitations in dealing with multifrequencies simultaneously, halting and limiting some applications. Here, we report a fast and data-driven spectrometer built with a one-dimensional array of single-photon-sensitive avalanche diodes. We report observing the HBT effect for multiple frequencies at the same time. In particular, we observe the HBT effect for up to five lines of the Ne spectrum, but this can be improved upon to include more lines. Our work represents a major step in making spectral binning and multifrequency HBT more widely available. The technology we present can benefit both classical and quantum applications.