The deep integration of communication and sensing technology in fiber-optic systems has been highly sought after in recent years, with the aim of rapid and cost-effective large-scale upgrading of existing communication cables in order to monitor ocean activities. As a proof-of-concept demonstration, a high-degree of compatibility was shown between forward-transmission distributed fiber-optic vibration sensing and an on–off keying (OOK)-based communication system. This type of deep integration allows distributed sensing to utilize the optical fiber communication cable, wavelength channel, optical signal and demodulation receiver. The addition of distributed sensing functionality does not have an impact on the communication performance, as sensing involves no hardware changes and does not occupy any bandwidth; instead, it non-intrusively analyzes inherent vibration-induced noise in the data transmitted. Likewise, the transmission of communication data does not affect the sensing performance. For data transmission, 150 Mb/s was demonstrated with a BER of 2.8 × 10⁻⁷ and a Q_dB of 14.1. For vibration sensing, the forward-transmission method offers distance, time, frequency, intensity and phase-resolved monitoring. The limit of detection (LoD) is 8.3 pε/Hz^1/2 at 1 kHz. The single-span sensing distance is 101.3 km (no optical amplification), with a spatial resolution of 0.08 m, and positioning accuracy can be as low as 10.1 m. No data averaging was performed during signal processing. The vibration frequency range tested is 10–1000 Hz.

For distributed fiber-optic sensors, slowly varying vibration signals down to 5 mHz are difficult to measure due to low signal-to-noise ratios. We propose and demonstrate a forward transmission-based distributed sensing system, combined with a polarization-generated carrier for detection bandwidth reduction, and cross-correlation for vibration positioning. By applying a higher-frequency carrier signal using a fast polarization controller, the initial phase of the known carrier frequency is monitored and analyzed to demodulate the vibration signal. Only the polarization carrier needs to be analyzed, not the arbitrary-frequency signal, which can lead to hardware issues (reduced detection bandwidth and less noise). The difference in arrival time between the two detection ends obtained through cross-correlation can determine the vibration position. Our experimental results demonstrate a sensitivity of 0.63 mrad/με and a limit of detection (LoD) of 355.6 pε/Hz^1/2 at 60 Hz. A lock-in amplifier can be used on the fixed carrier to achieve a minimal LoD. The sensing distance can reach 131.5 km and the positioning accuracy is 725 m (root-mean-square error) while the spatial resolution is 105 m. The tested vibration frequency range is between 0.005 Hz and 160 Hz. A low frequency of 5 mHz for forward transmission-based distributed sensing is highly attractive for seismic monitoring applications.

Smart cables extend submarine communication infrastructure toward marine environmental sensing and sensing-data backhaul. This paper investigates a multi-core fiber (MCF)-based prototype in which high-speed communication traffic and discrete-sensor data are routed through different spatial cores rather than sharing the same optical core. A 100 km weakly coupled four-core MCF was characterized and used as the central spatial-routing section, with two cores assigned to bidirectional communication and two cores to bidirectional sensing-data backhaul. At 1625 nm, the measured inter-core crosstalk (IC-XT) values for the four reported measurements were $-53.1$, $-52.6$, $-51.2$, and $-53.7$ dB/100 km. The same MCF section was incorporated into repeatered and unrepeatered hybrid laboratory configurations, with additional single-mode-fiber spans extending the total link lengths to 500 km and 300 km, respectively. Under the tested 400 Gbps condition, no frame loss or system alarm was observed during 17 h of operation; the round-trip delay was approximately 2.35 ms and the packet jitter remained below $0.3\mathsf{\mu }\mathrm{s}$. The sensing-node velocity channels recorded transient vibration responses and long-duration spectral distributions consistent with those of a reference CDS-E20 seismometer. These results support the feasibility of spatial-core routing for MCF-based smart cable prototypes.

Conventional repeatered optical communication systems face inherent limitations in terms of reliability, flexibility in optical fiber configuration, and power supply modes, particularly when applied to large-scale cabled ocean observatories, which have highly variable load demands. To address these challenges, a novel hybrid optimization algorithm (GA + PSO + SA) has been developed to enable simultaneous optimization of multiple critical parameters, including the pump light wavelength, the length of the erbium-doped fiber, and the placement of the remote optical amplifier. This approach represents a significant advancement over conventional single-algorithm methods because it effectively overcomes local optima and achieves global performance optimization. Comprehensive simulations and experimental validation demonstrate that the optimized unrepeatered system achieves transmission distances of 691.8 km using G.654E fibers and over 400 km with standard G.652D fibers, while maintaining excellent signal quality and exceptional stability. This work provides a systematic framework for the design and optimization of ultra-long-haul unrepeatered systems, highlighting their practical applicability in cabled ocean observatories.