This research designed an energy management system involving a battery-supercapacitor Hybrid Energy Storage System (HESS) for electric vehicles (EV). The objective is to improve the performance of the HESS by combining battery and supercapacitor features, accounting for topographical information to guarantee continuous hybridization during the drive cycle. Contour Positioning System (CPS) was used to determine the slope of the rode travelled by the vehicle. Two adaptive algorithms were designed for a rule-based controller to control the energy shared between the battery and the supercapacitor; an optimal adaptive controller and fuzzy adaptive controller. The HESS model, electric vehicle and controllers were tested using MATLAB/Simulink with three real drive cycles, namely, uphill, downhill and city tour, in three different speeds 50Km/h, 60Km/h and 70 Km/h. The results proved the controllers managed to extend battery life-cycle by reducing the stress on the battery for the drive cycles. The results were compared in terms of energy consumption for the optimal adaptive rule-based controller and fuzzy adaptive rule-based controller. The optimal adaptive rule-based controller guaranteed the HESS was able to operate continuously and extend the number of drive cycles in a wide range of speeds and road slopes.
The energy storage system (ESS) plays a crucial role in electric vehicles (EVs), impacting their performance and efficiency. While batteries are the standard choice for energy storage, they come with drawbacks like low power density and limited life cycles, which can hinder pure battery electric vehicles (PBEVs). To address these issues, a hybrid energy storage system (HESS) that combines a battery with a supercapacitor provides a more effective solution. The battery delivers consistent power, while the supercapacitor manages peak power demands and regenerative braking energy. This study proposes a new energy management strategy for the HESS, an advanced adaptive rule-based algorithm. The results of the standard rule-based and adaptive rule-based algorithms are used to verify the proposed control algorithm. The system was modeled in MATLAB/Simulink and evaluated across three driving cycles—UDDS, NYCC, and Japan1015—while varying states of charge for the supercapacitors. The findings indicate that the HESS significantly alleviates battery stress compared to a pure battery system, enhancing both efficiency and lifespan. Among the algorithms tested, the advanced adaptive rule-based algorithm yielded the best results, increasing the number of viable drive cycles.
Supercapacitors are an energy storage device used in the automotive industry. Due to its low energy density, it is difficult to use only supercapacitors in applications. DC-DC converters are used alongside the supercapacitor to maintain the terminal voltage of the supercapacitors. This research proposes a block-box model to represent the behaviour of boost DC-DC converter with supercapacitor module. Real set of signals were collected experimentally from the boost DC-DC converter to estimate transfer function. The NI compact DAQ-9184 was used to capture the experimental measurements, and Matlab System Identification Toolbox was used to identify discrete transfer function. The PID controller had been designed using the estimated transfer function then the model was verified by the SimPowerSystems model of boost DC-DC converter. The Simulation result proves the estimated transfer function of the boost DC-DC converter represent its actual behavior.
1 January 2021 in Advances in Science, Technology and Engineering Systems Journal
This research aims to design and control the Hybrid Energy Storage System (HESS). The HESS had been designed by combined the battery and supercapacitor. A lead-acid battery, supercapacitor module and DC-DC converter were used to build the parallel topology of HESS. The battery connected directly to the dc bus, while, the supercapacitor module was connect to the to the dc bus via bidirectional DC-DC converter. The Linear Quadratic Regulator (LQR) had been used to drive the DC-DC converter. The HESS and the proposed LQR controller simulate in MATLAB/Simulink environment. The response of the proposed controller had been analysed for different coefficients of LQR. The simulation results of LQR show a stable response of the suggested HESS over a wide load range. This hybridization will improve the reliability of HESS and increase the battery life-cycle.
This paper deals with the design and modeling aspects of the Ni-MH (Nickle metal hydride) battery and measures the SOC (State of charge) using different methods. This research deals with mathematical modeling, analysis of stability, analysis of step response, ABCD matrix, controllability, observability and peak percentage of the battery system. In addition, the output of the battery model is observed in Simulink. After that, the critically damped state-space design method by using state feedback method is discussed and implemented in Simulink. The battery model is implemented in Simulink using DC machine for charge and discharge and two ways of SOC estimation discuss with implementation in Simulink. From the implementations of the two methods of the SOC measurements, it is concluded that the direct measurement method is a superior method to estimate the SOC of the battery.