The Amazon rainforest, spanning multiple countries in South America, is the world’s largest equatorial expanse, housing a vast array of relatively unknown plant and animal species. Encompassing the planet’s greatest flora, the Amazon offers a tremendous variety of plants from which natural lignocellulosic fibers (NLFs) can be extracted. In this century, NLFs, which have long been utilized by indigenous populations of the Amazon, have garnered interest as potential reinforcements for composites, whether polymer- or cement-based, in various technical applications such as packaging, construction, automotive products, and ballistic armor. A comparison with synthetic materials like glass, carbon, and aramid fibers, as well as other established NLFs, highlights the cost and specific property advantages of Amazon natural fibers (ANFs). Notably, the sustainable cultivation and extraction of ANFs, as alternatives to deforestation and livestock pasture, contribute to the preservation of the Amazon rainforest. This review article provides a comprehensive examination of recent studies directly related to ANF-reinforced polymer matrix composites. The specific advantages, proposed applications, and reported challenges are highlighted, shedding light on the potential of these unique natural fibers.
2 August 2024 in OBSERVATÓRIO DE LA ECONOMÍA LATINOAMERICANA
In this study, nanometric powders of silicon carbide (SiC), micrometric alumina (Al₂O₃) and yttria (Y₂O₃), with specific characteristics provided by the manufacturers, were used to investigate the compaction behavior and the resulting properties after sintering. The SiC used has a purity of over 99% and a particle size distribution with a d50 of 40 nm, while Al₂O₃ and Y₂O₃ have purities of 99.8% and 99.995%, respectively. The morphological evaluation of the powders was carried out using scanning electron microscopy (SEM), while the apparent density analysis was conducted using gas pycnometry. SiC mixtures with 1% and 5% Al₂O₃ and Y₂O₃ were prepared and subjected to uniaxial compaction tests to determine densification behavior under different pressures. The results of this study are relevant to the development of ceramic materials with optimized properties for a wide range of industrial applications. The addition of small amounts of oxides to SiC does not compromise its compaction properties, maintaining the effectiveness of the sintering process and resulting in materials with high density and improved mechanical properties.
2 August 2024 in OBSERVATÓRIO DE LA ECONOMÍA LATINOAMERICANA
This work investigated the sintering of silicon carbide (SiC) with alumina (Al2O3) and yttria (Y2O3) additives by hot pressing. Mixtures of SiC with 1% and 5% Al2O3 and Y2O3 were used, pressed at 1800 °C and 1850 °C, resulting in specimens that were characterized in terms of density, microstructure, Vickers hardness and fracture toughness. The addition of 5% oxide additives provided greater densification and better mechanical properties. The temperature of 1800 °C proved to be the most effective for sintering due to the microstructure presented. The analysis revealed a homogeneous distribution of additives and grains, concluding that the 5% additive is considerably superior for increasing the densification and mechanical strength of SiC.
1 August 2024 in Contribuciones A Las Ciencias Sociales
In this study, the addition of lignin granules to the asphalt binder PAC 30/45 and its effects on short-term aging were investigated. Penetration, softening point, and ductility tests were conducted before and after RTFOT (Rolling Thin Film Oven Test). Laboratory results revealed that incorporating lignin into the asphalt binder significantly improved aging resistance compared to the pure binder. This was evidenced by reduced penetration, increased consistency, higher softening point, and satisfactory ductility after aging. Lignin also decreased the binder's sensitivity to temperature variation, indicated by a Thermal Susceptibility Index (TSI) closer to zero. While improvements were not as pronounced as in previous studies with PAC 50/70, adding 3% lignin showed benefits compared to the unmodified binder, whereas 6% lignin made PAC 30/45 more susceptible to oxidation. It is concluded that lignin can enhance the rheological properties of PAC 30/45, increasing its stiffness, durability, and aging resistance. Further exploration of lignin concentrations below 3% and above 6% is recommended to better understand oxidative effects on the 30/45 binder and confirm the benefits of minor additions.
1 October 2024 in OBSERVATÓRIO DE LA ECONOMÍA LATINOAMERICANA
This research developed an HDPE composite reinforced with Al2O3 and 1% SiC in the proportions of pure HDPE, 40 %, 50 % and 60 % of ceramic load. The mechanical flexural test showed results of sMAX 19.09 ± 2.89 MPa and E 1806 ± 400 MPa for the A60 group and concluded that with ceramic loadings above 60 % contribute to crystallization in the regions around the particles. TGA analysis showed initial degradation at 409 °C and final degradation between 499 and 504 °C, with a residue in pure HDPE of 0.46%. The DSC curves showed an endothermic peak at 132 °C and crystallization around 119 °C, and the crystallinity of the HDPE was 95.29 %, and the analyses showed a decrease in the enthalpy of fusion and crystallization with increasing ceramic loading due to the decrease in the polymer fraction in the composite. DMA analysis showed that temperatures above the Tg of the crystalline phases were the mechanism that contributed most to the storage modulus. FTIR analysis showed several interactions in different bands between the 3 compounds in the composite.