Photon-number resolving transition-edge sensors (TESs) with near unity system detection efficiency enable novel approaches to quantum computing, for example, heralding robust Gottesman–Kitaev–Preskill qubit states. Increasing the speed of the detectors increases the rate at which these states can be heralded. In addition, depending on the details of the scheme, faster detectors can reduce the complexities of the hardware implementation. In previous work, we demonstrated that adding a small amount of gold between the tungsten film and silicon substrate can increase thermal conductance and reduce detector recovery time. In that study, the readout electronics imposed limitations on stable biasing conditions of the TES detector, and the TES could only be biased at higher than ideal values. In this report, we demonstrate the operation of the TES illuminated by a heavily attenuated pulsed laser running at 1 MHz repetition rate and examine the limits to adding gold to speed up device recovery times using a higher bandwidth readout system. The best performance was achieved by combining a 15×15μm2 tungsten TES with 5μm3 of gold, which resulted in a recovery time faster than 250 ns, with an energy resolution of 0.25 eV full-width at half maximum at 0.8 eV photon energy.
5 December 2018 in IEEE Transactions on Applied Superconductivity
The current state-of-the-art approach for SIS junction fabrication is based on magnetron sputtering and the Gurvitch Al overlayer trilayer process where an Al overlayer is deposited onto the Nb base electrode in order to subsequently grow a critical ~1 nm AlOx or AlN tunnel barrier. While the switch from AlOx to AlN barriers has significantly increased the achievable critical current density, and significant research has been performed to understand and optimize ICP AlN growth, the use of Nb electrodes provides an upper limit to the frequency range for low-noise operation when employed in THz mixer applications, and has lead to the study and use of alternative materials with higher transition temperatures (Tc) such as NbN and NbTiN. The Nb electrodes also impose stringent cooling requirements, replacement of both electrodes with higher Tc materials can increase the required device operating temperature to 10 K, thus reducing the power consumption of the refrigeration system, a building block for the realization of more energy efficient superconducting computing systems, such as those based on single-flux-quantum (SFQ) logic [6], [7], [8], [9]. In this work, we have departed from conventional SIS material growth techniques through the use of an alternative materials deposition technology - Reactive Bias Target Ion Beam Deposition (RBTIBD) - that offers unique capabilities to tailor materials and interfaces. Using RBTIBD technology, we have realized the first ever NbTiN/AlN/NbTiN SIS junctions with highest yet reported sum-gap voltages exceeding 5.0 mV, potentially extending the theoretical limit of low-loss SIS mixing applications beyond 1.2 THz and relaxing the cooling requirements for superconducting device applications.
9 April 2019 in IEEE Transactions on Applied Superconductivity
Nb-based superconducting alloys, such as NbN and NbTiN, can have a superconducting energy gap near twice that of elemental Nb, thus, being ideal candidates for low-loss superconducting circuits operating above the gap frequency of Nb. We are particularly interested in these materials for THz-frequency superconducting-insulating-superconducting (SIS) mixers, kinetic inductance detectors, and traveling wave kinetic inductance parametric amplifier devices. We recently reported the use of an alternative synthesis technique, reactive bias target ion beam deposition (RBTIBD), used to realize high-quality NbTiN films and high-energy gap NbTiN/AlN/NbTiN SIS heterostructures. In this paper, the effect of post-deposition annealing on the electrical and structural properties of room temperature deposited RBTIBD NbTiN was investigated. Our room temperature RBTIBD NbTiN films were annealed using rapid thermal annealing from 200 to 1000 $^\circ$ C. The change in structural and electrical properties was characterized by X-ray diffraction, atomic force microscopy, and four-point probe measurements. The annealed films demonstrated an enhancement in transition temperature (T $_c$ ), increased crystallinity, larger grain size, and significantly reduced intrinsic stress.
This study investigates the potential of fluorescence imaging in conjunction with an original, fused segmentation framework for enhanced detection and delineation of brain tumor margins. By means of a test bed optical microscopy system, autofluorescence is utilized to capture gray level images of brain tumor specimens through slices, obtained at various depths from the surface, each of 10 µm thickness. The samples used in this study originate from tumor cell lines characterized as Gli36ϑEGRF cells expressing a green fluorescent protein. An innovative three-step biomedical image analysis framework is presented aimed at enhancing the contrast and dissimilarity between the malignant and the remaining tissue regions to allow for enhanced visualization and accurate extraction of tumor boundaries. The fluorescence image acquisition system implemented with an appropriate unsupervised pipeline of image processing and fusion algorithms indicates clear differentiation of tumor margins and increased image contrast. Establishing protocols for the safe administration of fluorescent protein molecules, these would be introduced into glioma tissues or cells either at a pre-surgery stage or applied to the malignant tissue intraoperatively; typical applications encompass areas of fluorescence-guided surgery (FGS) and confocal laser endomicroscopy (CLE). As a result, this image acquisition scheme could significantly improve decision-making during brain tumor resection procedures and significantly facilitate brain surgery neuropathology during operation.
1 April 2019 in IEEE Transactions on Applied Superconductivity
High energy gap Nb-based superconducting alloys with low normal state resistivity are fundamentally important for realization of low-loss high frequency circuits operating above the typical ~670 GHz gap frequency of elemental Nb. NbTiN has been shown to have a superconducting energy gap nearly twice that of elemental Nb, and is emerging as an important material for various detector and superconducting computing technologies. In this study, we report on the growth of high-quality face-centered cubic (FCC) NbTiN films through the use of an alternative materials deposition technology - Reactive Bias Target Ion Beam Deposition (RBTIBD). This novel technique offers more degrees of freedom compared to conventional sputtering, notably through decoupling the plasma generation and target bias, through use of a hollow-cathode ion source and independently pulse biased sputtering targets. The reported films are of high quality, with increased transition temperatures, and reduced normal state resistivity and surface roughness, compared to our previously reported reactive magnetron sputtered NbTiN films. In particular, at UVA, we are investigating these NbTiN films for widebandgap all NbTiN superconducting-insulating-superconducting (SIS) mixers, kinetic inductance detectors (KID), and traveling-wave kinetic inductance parametric amplifier (TKIP) devices.
2 April 2019 in IEEE Transactions on Applied Superconductivity
High quality Nb-based superconductor-insulator- superconductor (SIS) junctions with aluminum oxide tunnel barriers grown from Al overlayers are broadly reported in the literature. However, as the current density increases, aluminum oxide tunnel barriers yield significant leakage current due to the pinholes and defects in the tunnel barrier. In this work, the growth dynamics of AlN are studied through the inductively coupled plasma (ICP) nitridation of an Al overlayer at an increased sample to ICP distance with the modification of the university of Virginia (UVA) trilayer deposition system. The new ICP geometry follows the previous UVA optical spectroscopy investigation of the plasma at the wafer, but now also allows spectroscopy measurement in the vicinity of the ICP source via an additional quartz window. We report a significantly slower nitridation growth rate, while maintaining the relative dissociation (RD), at the larger growth distance. High quality, low leakage SIS I(V) characteristics with current densities exceeding 30 kA/cm2 and better control of RnA are obtained.