In the present work, growth of single crystals of chalcone derivatives {4-[(1E)-3-(4-methylphenyl)-3-oxoprop-1-en-1-yl]phenyl 4-methylbenzene-1-sulfonate} (4M1PMS) and {4-[(1E)-3-(4-bromophenyl)-3-oxoprop-1-en-1-yl]phenyl4-methylbenzene-1-sulfonate} (4BPMS), at room temperature is reported. The spectroscopic techniques are used to identify the presence of functional groups in the materials. The single-crystal XRD and powder XRD analysis reveals that 4M1PMS belongs to non-centrosymmetric ( ) and 4BPMS belongs to centrosymmetric crystalline system. The molecular structures exhibit C–H…O and π...π intermolecular interactions. From UV/VIS/NIR spectroscopic studies, it is found that both samples have bathochromic shifts in linear absorbance (cut-off region) spectra. The broad emission region involved in several sharp emission peaks in blue region, exhibits a blue light emission property, as observed from photoluminescence study, in both the samples. The thermal stability of the materials were studied by TGA/DTA techniques and crystals were thermally stable until the melting point. In NLO study, 4M1PMS crystal has shown SHG efficiency 2.2 times that of KDP crystal. In addition, electronic contribution in hyperpolarizability (first order and second order) tensors of both the compounds were computed theoretically by M06-2X functional at DFT level. The open/closed aperture Z-scan technique were performed to evaluate third order nonlinear optical materials by measuring experimental parameters such as nonlinear absorption/refraction and calculate second-order hyperpolarizability with corresponding third-order nonlinear optical susceptibility of 4M1PMS and 4BPMS. The surface damage threshold studies of 4M1PMS and 4BPMS were performed by Q-switched Nd:YAG laser at 532 nm.
Highly efficient broadband absorbing surfaces covering the UV, visible and near-IR regions are of great importance for low-light imaging devices, optical devices and optoelectronic devices. In this work, we demonstrate the fabrication of remarkably efficient absorbing surfaces due to the formation of nanoflower-like cavity structures on a stainless steel (SS304) surface, along with micropatterning in a hierarchical fashion. The fabrication process is carried out using noncontact, programmable, single-step laser irradiation by an inexpensive and robust 532 nm nanosecond laser. The measured specular antireflection properties over a wide spectral region (250–1800 nm) are extremely low, less than 0.5%, over a large range of incident angles and for both orthogonal polarizations. These special hierarchical structures with nanorods, nanoparticles, and nanocavities, completely trap the photon incident on these surfaces due to multiple reflections. These surface structures evolve with time to give better nanostructured features with higher oxygen content on the surfaces, revealed by FESEM elemental analysis, which increases the ability to trap photons. We believe these antireflection surfaces, with high efficiencies and long-term stability, will play a vital role in many modern technological applications.
29 October 2021 in Journal of Physics D: Applied Physics
The anisotropic droplet formulation is generalized from hydrophilic to superhydrophobic surfaces. An experimental method to calibrate the ellipsoidal droplet volume on both hydrophilic and hydrophobic surfaces is presented. A broad range of contact angles (CAs) is produced on the copper and stainless-steel surfaces using femtosecond laser patterning. The effects of line spacing between the laser scanning on the formation of anisotropic CAs are discussed. The comparative study of the evolution of anisotropic CAs and droplet’s spreading dynamics are studied on both surfaces. According to the triple contact line (TCL) theory, CAs are determined by the TCL between droplet and surface rather than the contact area. We presented the mathematical formalism and the experimental validity of the TCL theory on ellipsoidal droplets over a broad range of CAs, from as low as 37°–172°. This work experimentally validated the TCL theory over a broad range of CAs with good confidence.
5 July 2019 in Surface Topography: Metrology and Properties
Superhydrophobic copper surfaces with contact angle (CA) as high as 158° are fabricated using the one-step process of femtosecond fiber laser writing. Low spacing between the laser scanning lines was chosen purposefully to observe the anisotropic surface structures on the copper surfaces. This resulted in the formation of an ellipsoidal water droplet with anisotropic CAs, which are different along the major and minor axes. We quantified an experimentally measured parameter that correlates the droplet anisotropy and is related to the one-dimensional root mean square surface height deviation (1D RMS SHD). Theoretical CAs prediction based on triple contact line (TCL) theory on an ellipsoidal droplet volume is formulated and the calculations are in excellent agreement with experimentally observed anisotropic CAs. We presented an analytical expression for effective volume function relating the anisotropic contact angles, height, and the three semi-major axes of the ellipsoidal droplet. These functional values and observed contact angles are falling within the experimental errors of less than 5%. This work strengthens the validity of TCL theory. Our method of fabrication, high CAs results, correlation with 1D RMS SHD and theoretical prediction of elliptical CAs on an anisotropic surface will guide to design surfaces for many future applications.
This study aimed to assess the antimicrobial activity of endophytic Phyllosticta fallopiae L67 isolated from Aloe vera against diabetic wound microorganisms and characterise their active fraction for biologically important metabolites. The dichloromethane (DCM) extract exhibited the most significant activity with inhibition zones ranging from 11.33 to 38.33 mm. The minimal inhibitory and lethality concentrations of DCM extract ranged from 78.13 to 2500.00 µg/ml and 625.00 to 5000.00 µg/ml, respectively. The extract showed teratogenicity and lethality in the zebrafish model, where peritoneal and hepatic oedema occurred at 62.50 µg/ml, and no abnormality appeared at 31.25 µg/ml. The extract also inhibited more than 82% biofilm formation. Bioassay-guided fractionation on DCM extract yielded 18 fractions and the most active fraction was subjected to UPLC-QTOF-MS/MS analysis. Flavones, stilbenes, flavanonols, isoflavonoids, phenolic glycosides and phenol derivatives were detected. In conclusion, endophytic P. fallopiae possessed bioactive metabolites with significant antimicrobial activity against diabetic wound microorganisms. Graphical Abstract
Here, we present a simple and green method of preparing Au-Ag bimetallic nanoparticles (NPs) with a tunable surface plasmon resonance (SPR) wavelength by using picosecond laser irradiation. Au-Ag alloy NPs have been produced by irradiating the solutions containing respective metallic salts in a polyvinyl alcohol (PVA) matrix using a picosecond laser in a single-step process. The SPR wavelength of the Au-Ag bimetallic NPs is observed to be shifted/changed with the Au-Ag concentration and the laser irradiation parameters. The Au-Ag NPs embedded in the PVA matrix are advantageous for Surface-Enhanced Raman scattering (SERS) applications. The estimated enhancement factors (EFs) were observed to vary as a function of conditions of the Au-Ag bimetallic alloy NPs synthesis and also on the concentration of Au at a fixed input fluence of irradiation. The SERS active platforms of Au-Ag bimetallic NPs showed EFs as high as of the order of 108 for Crystal Violet (CV) dye samples at nano molar concentrations. The present study demonstrates a simple, single-step, and green method that fabricates Au-Ag alloy-based nanocomposites suitable for SERS investigations with significantly higher orders of EFs.