JungHwan Park

Mr. JungHwan Park

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 April 2023 in Crystals
Verified
Journal Article
Open access
PDF file
JKJUNA KIM
JUNA KIM
JPJungHwan Park
JungHwan Park
SPSang-Goen Park
Sang-Goen Park
CSChang Sik Son
Chang Sik Son
YSYoung Guk Son
Young Guk Son
DHDonghyun Hwang
Donghyun Hwang
In the present study, Cu2O films were deposited on a glass substrate via RF (radio frequency) magnetron sputtering under substrate temperature conditions that ranged from room temperature (RT, 25 °C) to 400 °C. The structural, compositional, and optical properties of the Cu2O films were analyzed in relation to the experimental variables by applying various measurement methods. The substrate temperature was a crucial factor in shaping the structural, compositional, and optical properties of the Cu2O films that were synthesized via RF-magnetron sputtering. Our findings revealed that the Cu2O films exhibited a cubic structure, which was confirmed by XRD analysis. Specifically, the (111) and (200) planes showed different trends with respect to the substrate temperature. The intensity of the (111) peak increased at 250 °C, and above 300 °C, the preferred orientation of the (111) plane was maintained. The grain size, which was determined via FE-SEM, displayed a positive correlation with the substrate temperature. Additionally, XPS analysis revealed that the binding energy (BE) of the Cu2O film sputtered at 400 °C was similar to that which was previously reported. Notably, the as-grown Cu2O film demonstrated the highest transmittance (15.9%) in the visible region, which decreased with increasing substrate temperature. Furthermore, the energy band gap (Eg) of the Cu2O films remained constant (2.51 eV) at low substrate temperatures (25 °C to 200 °C) but exhibited a slight increase at higher temperatures, reaching 2.57 eV at 400 °C.

27 December 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
SLSeok-Hee Lee
Seok-Hee Lee
HCHyunJin Cha
HyunJin Cha
JPJungHwan Park
JungHwan Park
CSChang Sik Son
Chang Sik Son
YSYoung Guk Son
Young Guk Son
DHDonghyun Hwang
Donghyun Hwang
In this study, a porous Ni-foam support was employed to enhance the capacitance of nickel cobaltite (NiCo2O4) electrodes designed for supercapacitors. The hydrothermal synthesis method was employed to grow NiCo2O4 as an active material on Ni-foam. The NiCo2O4 sample derived from hydrothermal synthesis underwent subsequent post-heat treatment at temperatures of 250 °C, 300 °C, and 350 °C. Thermogravimetric analysis of the NiCo2O4 showed that weight loss due to water evaporation occurs after 100 °C and enters the stabilization phase at temperatures above 400 °C. The XRD pattern indicated that NiCo2O4 grew into a spinel structure, and the TEM results demonstrated that the diffraction spots (DSs) on the (111) plane of the sample annealed at 350 °C were more pronounced than those of other samples. The specific capacitance of the NiCo2O4 electrodes exhibited a decrease with increasing current density across all samples, irrespective of the annealing temperature. The electrode annealed at 350 °C recorded the highest specific capacitance value. However, the capacity retention rate of the NiCo2O4 electrode revealed a deteriorating trend, declining to 88% at 250 °C, 75% at 300 °C, and 63% at 350 °C, as the annealing temperature increased.

25 July 2024 in Coatings
Verified
Journal Article
Open access
PDF file
JPJungHwan Park
JungHwan Park
YSYoung Guk Son
Young Guk Son
CSChang Sik Son
Chang Sik Son
DHDonghyun Hwang
Donghyun Hwang
This study examines the impact of varying oxygen flow rates on the properties of Cu2O thin films deposited via radio frequency (RF) magnetron sputtering. X-ray diffraction (XRD) analysis showed a phase transition from cubic Cu2O to a mixed Cu2O and CuO phase, eventually forming a Cu4O3 tetragonal structure as oxygen content increased. The surface morphology and cross-sectional structure of Cu2O thin films observed through field emission scanning electron microscopy (FE-SEM) were found to vary significantly depending on the oxygen flow rate. X-ray photoelectron spectroscopy (XPS) indicated notable variations in the chemical states of copper and oxygen. The Cu 2p spectra revealed peaks around 933 eV and 953 eV for all samples, with the S01 sample (deposited with only argon gas) exhibiting the lowest intensity. The S02 sample showed the highest peak intensity, which then gradually decreased from S03 to S06. The O 1s spectra followed a trend with peak intensity being highest in S02 and decreasing with further oxygen flow rates, indicating the formation of complex oxides such as Cu4O3. UV-Vis-NIR spectroscopy results demonstrated a decrease in transmittance and optical band gap energy with increasing oxygen content, suggesting a decline in crystallinity and an increase in defects and impurities. These findings underscore the critical role of precise oxygen flow rate control in tailoring the structural, morphological, compositional, and optical properties of Cu2O thin films for specific electronic and optical applications.

24 December 2024 in Crystals
Verified
Journal Article
Open access
PDF file
JPJungHwan Park
JungHwan Park
CSChang Sik Son
Chang Sik Son
YSYoung Guk Son
Young Guk Son
DHDonghyun Hwang
Donghyun Hwang
Cu2O thin films were deposited on soda-lime glass substrates using RF magnetron sputtering under various process pressures, and their structural, morphological, compositional, and optical properties were investigated. X-ray diffraction (XRD) revealed that the films crystallized in the cubic Cu2O phase, with the highest crystallinity observed at 5 mTorr, as evidenced by the sharp and intense (111) peak. Raman spectroscopy confirmed the predominance of Cu2O vibrational modes across all samples, with improved phase purity and crystallinity at 5 mTorr and 10 mTorr. Field-emission scanning electron microscopy (FE-SEM) showed that the films deposited at 5 mTorr and 10 mTorr exhibited densely packed, well-defined grains, while those at 1 mTorr and 15 mTorr displayed irregular or poorly defined morphologies. X-ray photoelectron spectroscopy (XPS) confirmed the presence of Cu(I) without significant secondary phases, with slight surface oxidation observed at higher pressures. Optical characterization revealed that transmittance increased with pressure, reaching ~90% in the NIR range at 15 mTorr. The optical band gap (Eg) values increased from 2.34 eV at 1 mTorr to 2.43 eV at 15 mTorr with higher process pressure. Cu2O films deposited at 5 mTorr and 10 mTorr exhibited an optimal balance between high transparency and band gap values. These findings highlight the critical role of process pressure in determining the properties of Cu2O thin films and identify 5 mTorr as the optimal deposition condition for achieving high-quality films with superior structural and optical performance.