Young Guk Son

Prof. Young Guk Son


Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 January 2012 in Discover Nano
Verified
Journal Article
Open access
PDF file
DHDong Hyun Hwang
Dong Hyun Hwang
JAJung Hoon Ahn
Jung Hoon Ahn
KHK.N. Hui
K.N. Hui
Oscar K.S. HUIOscar K.S. HUI
Oscar K.S. HUI
YSYoung Guk Son
Young Guk Son
Zinc sulfide [ZnS] thin films were deposited on glass substrates using radio frequency magnetron sputtering. The substrate temperature was varied in the range of 100°C to 400°C. The structural and optical properties of ZnS thin films were characterized with X-ray diffraction [XRD], field emission scanning electron microscopy [FESEM], energy dispersive analysis of X-rays and UV-visible transmission spectra. The XRD analyses indicate that ZnS films have zinc blende structures with (111) preferential orientation, whereas the diffraction patterns sharpen with the increase in substrate temperatures. The FESEM data also reveal that the films have nano-size grains with a grain size of approximately 69 nm. The films grown at 350°C exhibit a relatively high transmittance of 80% in the visible region, with an energy band gap of 3.79 eV. These results show that ZnS films are suitable for use as the buffer layer of the Cu(In, Ga)Se2 solar cells.

5 February 2020 in Energies
Verified
Journal Article
Open access
PDF file
DSDonghyeok Shin
Donghyeok Shin
SLSangWoon Lee
SangWoon Lee
DKDong Ryeol Kim
Dong Ryeol Kim
JPJoo Hyung Park
Joo Hyung Park
YKYangdo Kim
Yangdo Kim
DHDonghyun Hwang
Donghyun Hwang
Copper sulfide (CuS) thin films were deposited on a glass substrate at room temperature using the radio-frequency (RF) magnetron-sputtering method at RF powers in the range of 40–100 W, and the structural and optical properties of the CuS thin film were investigated. The CuS thin films fabricated at varying deposition powers all exhibited hexagonal crystalline structures and preferred growth orientation of the (110) plane. Raman spectra revealed a primary sharp and intense peak at the 474 cm−1 frequency, and a relatively wide peak was found at 265 cm−1 frequency. In the CuS thin film deposited at an RF power of 40 W, relatively small dense particles with small void spacing formed a smooth thin-film surface. As the power increased, it was observed that grain size and grain-boundary spacing increased in order. The binding energy peaks of Cu 2p3/2 and Cu 2p1/2 were observed at 932.1 and 952.0 eV, respectively. Regardless of deposition power, the difference in the Cu2+ state binding energies for all the CuS thin films was equivalent at 19.9 eV. We observed the binding energy peaks of S 2p3/2 and S 2p1/2 corresponding to the S2− state at 162.2 and 163.2 eV, respectively. The transmittance and band-gap energy in the visible spectral range showed decreasing trends as deposition power increased. For the CuS/tin sulfide (SnS) absorber-layer-based solar cell (glass/Mo/absorber(CuS/SnS)/cadmium sulfide (CdS)/intrinsic zinc oxide (i-ZnO)/indium tin oxide (ITO)/aluminum (Al)) with a stacked structure of SnS thin films on top of the CuS layer deposited at 100 W RF power, an open-circuit voltage (Voc) of 115 mA, short circuit current density (Jsc) of 9.81 mA/cm2, fill factor (FF) of 35%, and highest power conversion efficiency (PCE) of 0.39% were recorded.

9 April 2023 in Crystals
Verified
Journal Article
Open access
PDF file
JKJUNA KIM
JUNA KIM
JPJungHwan Park
JungHwan Park
SPSang-Goen Park
Sang-Goen Park
CSChang Sik Son
Chang Sik Son
YSYoung Guk Son
Young Guk Son
DHDonghyun Hwang
Donghyun Hwang
In the present study, Cu2O films were deposited on a glass substrate via RF (radio frequency) magnetron sputtering under substrate temperature conditions that ranged from room temperature (RT, 25 °C) to 400 °C. The structural, compositional, and optical properties of the Cu2O films were analyzed in relation to the experimental variables by applying various measurement methods. The substrate temperature was a crucial factor in shaping the structural, compositional, and optical properties of the Cu2O films that were synthesized via RF-magnetron sputtering. Our findings revealed that the Cu2O films exhibited a cubic structure, which was confirmed by XRD analysis. Specifically, the (111) and (200) planes showed different trends with respect to the substrate temperature. The intensity of the (111) peak increased at 250 °C, and above 300 °C, the preferred orientation of the (111) plane was maintained. The grain size, which was determined via FE-SEM, displayed a positive correlation with the substrate temperature. Additionally, XPS analysis revealed that the binding energy (BE) of the Cu2O film sputtered at 400 °C was similar to that which was previously reported. Notably, the as-grown Cu2O film demonstrated the highest transmittance (15.9%) in the visible region, which decreased with increasing substrate temperature. Furthermore, the energy band gap (Eg) of the Cu2O films remained constant (2.51 eV) at low substrate temperatures (25 °C to 200 °C) but exhibited a slight increase at higher temperatures, reaching 2.57 eV at 400 °C.

27 December 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
SLSeok-Hee Lee
Seok-Hee Lee
HCHyunJin Cha
HyunJin Cha
JPJungHwan Park
JungHwan Park
CSChang Sik Son
Chang Sik Son
YSYoung Guk Son
Young Guk Son
DHDonghyun Hwang
Donghyun Hwang
In this study, a porous Ni-foam support was employed to enhance the capacitance of nickel cobaltite (NiCo2O4) electrodes designed for supercapacitors. The hydrothermal synthesis method was employed to grow NiCo2O4 as an active material on Ni-foam. The NiCo2O4 sample derived from hydrothermal synthesis underwent subsequent post-heat treatment at temperatures of 250 °C, 300 °C, and 350 °C. Thermogravimetric analysis of the NiCo2O4 showed that weight loss due to water evaporation occurs after 100 °C and enters the stabilization phase at temperatures above 400 °C. The XRD pattern indicated that NiCo2O4 grew into a spinel structure, and the TEM results demonstrated that the diffraction spots (DSs) on the (111) plane of the sample annealed at 350 °C were more pronounced than those of other samples. The specific capacitance of the NiCo2O4 electrodes exhibited a decrease with increasing current density across all samples, irrespective of the annealing temperature. The electrode annealed at 350 °C recorded the highest specific capacitance value. However, the capacity retention rate of the NiCo2O4 electrode revealed a deteriorating trend, declining to 88% at 250 °C, 75% at 300 °C, and 63% at 350 °C, as the annealing temperature increased.

25 July 2024 in Coatings
Verified
Journal Article
Open access
PDF file
JPJungHwan Park
JungHwan Park
YSYoung Guk Son
Young Guk Son
CSChang Sik Son
Chang Sik Son
DHDonghyun Hwang
Donghyun Hwang
This study examines the impact of varying oxygen flow rates on the properties of Cu2O thin films deposited via radio frequency (RF) magnetron sputtering. X-ray diffraction (XRD) analysis showed a phase transition from cubic Cu2O to a mixed Cu2O and CuO phase, eventually forming a Cu4O3 tetragonal structure as oxygen content increased. The surface morphology and cross-sectional structure of Cu2O thin films observed through field emission scanning electron microscopy (FE-SEM) were found to vary significantly depending on the oxygen flow rate. X-ray photoelectron spectroscopy (XPS) indicated notable variations in the chemical states of copper and oxygen. The Cu 2p spectra revealed peaks around 933 eV and 953 eV for all samples, with the S01 sample (deposited with only argon gas) exhibiting the lowest intensity. The S02 sample showed the highest peak intensity, which then gradually decreased from S03 to S06. The O 1s spectra followed a trend with peak intensity being highest in S02 and decreasing with further oxygen flow rates, indicating the formation of complex oxides such as Cu4O3. UV-Vis-NIR spectroscopy results demonstrated a decrease in transmittance and optical band gap energy with increasing oxygen content, suggesting a decline in crystallinity and an increase in defects and impurities. These findings underscore the critical role of precise oxygen flow rate control in tailoring the structural, morphological, compositional, and optical properties of Cu2O thin films for specific electronic and optical applications.

23 September 2022 in Chemical Communications
Verified
Journal Article
Open access
PDF file
GJGi Ryeon Jo
Gi Ryeon Jo
MYMin Byeol Yun
Min Byeol Yun
YSYeong Hun Son
Yeong Hun Son
BPByeongjin Park
Byeongjin Park
JLJung-Goo Lee
Jung-Goo Lee
YBYoun-Kuoung Baek
Youn-Kuoung Baek
We report a simple and continuous spray-drying method to synthesize high-purity epsilon iron oxide (ε-Fe2O3). The strategy enables ferromagnetic resonance tuning, making it potentially usable in millimeter-wave absorbers.