According to the results of a dynamic prototype test for the surface outlet radial gate on the Jinping high arch dam during the flood discharging process, a novel cause of vibration fundamentally different from the traditional causes of flow-induced radial gate vibration, is analyzed for the first time. Under the condition that the flood is discharged only from mid-level outlets, an accompanying vibration of the surface outlet gate is induced by the vibration of the closely spaced mid-level outlet gates. It is counterintuitive that the most intense vibration occurs when the surface outlet gate is closed and, on the contrary, the vibration is reduced when the gate is opened and subjected to flow excitation. In order to analyze and explain this accompanying vibration phenomenon, a theoretical model is developed based on the conventional theory of passive vibration absorbers. The difference between the proposed and conventional theoretical models is that more complex load and damping conditions are considered, and more attention was paid to the dynamic behavior of the accessory structure. Then, the cause and mechanism for the surface outlet gate vibration is clarified in detail, based on the proposed theoretical model. The comprehensive analysis and mutual verification of the prototype test, theoretical derivation and numerical simulation, indicate that the clarification and the proposed theoretical model is reasonable and accurate. The research reported in this paper will be beneficial for the design, operation and maintenance of the hydraulic gates installed on high arch dams.
Ground and environmental vibrations induced by high dam flood discharge from the Xiangjiaba hydropower station (XHS) has significant adverse effects on nearby building safety and the physical and mental health of surrounding residents. As an effective approach to simulate the flow-induced vibration of hydraulic structures, the hydro-elastic experiment approach has been extensively applied and researched by Chinese scholars, but the relevant systematic research is rarely reported in international journals. Firstly, the hydraulic and structural dynamic similarity conditions that should be satisfied by the hydro-elastic model are briefly reviewed and derived. A hydro-elastic model of the XHS was further constructed using self-developed high-density rubber, and the vibration isolation system (including open trenches and flexible connects) was applied to avoid the external disturbances of pump operation, vehicle vibration and other experiments in the laboratory. Based on the data of model and prototype dynamic tests, a back propagation (BP) neural network was established to map the acceleration of the physical model to the ground in the prototype. In order to reduce the ground vibration, experiments were carried out to meticulously evaluate the ground vibration intensity under more than 600 working conditions, and the optimal operation scheme under different discharge volumes is presented here in detail. According to the prototype test data in 2013, 2014, and 2015, ground vibrations were significantly reduced by applying the presented optimal operation principle which indicates that the presented hydro-elastic approach and the vibration attenuation operation scheme were effective and feasible.
The stability of ship lift chamber operation has always been the key factor restricting the development of ship lift, which has not been well solved for a long time. With the development of upsizing of ships, the super-huge fully balanced ship lift with hoisting steel wire rope over 10000–15000 t is the development trend in the future. The mechanism of water loss and capsizing of multi-point ship lift is the most key scientific problem, and the most core technical problem is the layout and operation control of ship lift system. A generalized physical model of ship lift with the model scale of 1:33 was established to study the influence of multiple factors on water loss stability of ship chamber, such as gravity counterweight/torque counterweight ratio, water leakage flow, the position of suspension points among the chamber, quantity of the suspension points, and so on. Secondly, the structural dynamics equations of hoisting system is deduced in detail, considering the water fluctuation in the process of water loss caused by longitudinal capsizing moment influence on balance system, and research on the transient dynamic characteristics of hoisting system of the filtration process, determine the ship chamber conditions of stability for the trim through the Lyapunov stability criterion. The optimization calculation model of ship lift mechanical suspension system layout under the action of multiple constraints was established, and the effective measures will be given to improve the pitch stability. The results can provide technical guidance for the upsizing of ship lifters.
The working condition of water valve is an important sign of the success for navigation lock design, and the valve cavitation characteristics and suppression technology is the key technical challenge in the design of high head navigation lock, in the view of the “flat bottom & top spreading” with the condition of “less project quantities, convenient construction” simple type corridor with the head of 19 m in Qianwei ship lock, the method of combining the physical model test and prototype observation are both adopt to this research. Through the physical model test, the cavitation position, cavitation characteristics and the effect of natural ventilation on cavitation suppression are comprehensively determined by analyzing the change law of cavitation noise intensity from several cavitation noise sensors under different opening conditions during the opening process, also the visual observation of flow state and auditory observation. Prototype observation focuses on the effect of self-aerated technology of valve lintel. When the air pipe outside the value lintel position is closed, there are evident in the cavitation pulse signal, and the maximum strength can reach to 182Pa, the “crackling” of cavitation collapse could be clearly felt at the top of the value, occasionally with 2–3 times slight “muffled thunder”, The results show that the valve section has stronger cavitation during the opening process of value. On the contrary, when self-aerated of valve lintel was realized, the maximum ventilatory capacity was 0.169 m3/s, which was close to the 0.170 m3/s calculated by the physical model in the design stage, and no cavitation pulse signal was detected among the valve wells on both sides, and the process line was “stable” with the maximum noise intensity only about 10 Pa, no sound of cavitation collapse was heard at the top of the valve section during the whole valve opening process. The comparison of value steeve vibration also verifies the effect of self-aerated technology of valve lintel at the same times. The results show that self-aerated technology of valve lintel can significantly inhibit the cavitation of valve segment of this form.