Nano-treating is a novel concept wherein a low percentage of nanoparticles is used for microstructural control and property tuning in metals and alloys. The nano-treating of AA7075 was investigated to control its microstructure and improve its structural stability for high performance. After treatment with TiC nanoparticles, the grains were significantly refined from coarse dendrites of hundreds of micrometers to fine equiaxial ones smaller than 20 μm. After T6 heat treatment, the grains, with an average size of 18.5 μm, remained almost unchanged, demonstrating an excellent thermal stability. It was found that besides of growth restriction factor by pinning behavior on grain boundries, TiC nanoparticles served as both an effective nucleation agent for primary grains and an effective secondary phase modifier in AA7075. Furthermore, the mechanical properties of nano-treated AA7075 were improved over those of the pure alloy. Thus, nano-treating provides a new method to enhance the performance of aluminum alloys for numerous applications.
In this study, nano-sized fullerene C60 powder was sufficiently mixed with Cu2SnSe3 powder by ball milling method, and the C60/Cu2SnSe3 composites were prepared by spark plasma sintering technology. The fullerene C60 distributed uniformly in the form of clusters, and the average cluster size was less than 1 μm. With increasing C60 content, the electrical conductivity of C60/Cu2SnSe3 composites decreased, while the Seebeck coefficient was enhanced. The thermal conductivity of composites decreased significantly, which resulted from the phonon scattering by the C60 clusters located on the grain boundaries of the Cu2SnSe3 matrix. The highest figure of merit ZT of 0.38 was achieved at 700 K for 0.8% C60/Cu2SnSe3 composite.
Forming co-alloying solid solutions has long been considered as an effective strategy for improving thermoelectric performance. Herein, the dense Cu2−x(MnFeNi)xSe (x = 0–0.09) with intrinsically low thermal conductivity was prepared by a melting-ball milling-hot pressing process. The influences of nanostructure and compositional gradient on the microstructure and thermoelectric properties of Cu2Se were evaluated. It was found that the thermal conductivity decreased from 1.54 Wm−1K−1 to 0.64 Wm−1K−1 at 300 K via the phonon scattering mechanisms caused by atomic disorder and nano defects. The maximum zT value for the Cu1.91(MnFeNi)0.09Se sample was 1.08 at 750 K, which was about 27% higher than that of a pristine sample.
Magnesium alloys act as ideal biomedical materials with good biocompatibility. In this paper, the extruded biomedical Mg-6Zn-0.5Nd-0.5/0.8Ca alloys were prepared and their microstructure, mechanical properties and corrosion properties were investigated. The results showed that the surfaces of Mg-6Zn-0.5Nd-0.5/0.8Ca alloys extruded at medium temperature were smooth and compact without cracks. The tensile strength and elongation of Mg-6Zn-0.5Nd-0.5/0.8Ca alloys were 222.5 MPa and 20.2%, and 287.2 MPa and 18.4%, respectively. A large number of dislocations were generated in the grains and on grain boundaries after the extrusion. The alloy was immersed in simulating body fluid (SBF) for the weightlessness corrosion, and the corrosion products were analyzed by FTIR, SEM equipped with EDS. It was found that the corrosion rate of Mg-6Zn-0.5Nd-0.5Ca and Mg-6Zn-0.5Nd-0.8Ca alloy were 0.82 and 2.98 mm/a, respectively. Furthermore, the compact layer was formed on the surface of the alloy, which can effectively hinder the permeation of Cl− and significantly improve the corrosion resistance of magnesium alloys.