High-temperature heat pumps are a key technology for enabling the complete integration of renewables into the power grid. Although these systems may come with several variants, Brayton heat pumps are gaining more and more interest because of the higher heat sink temperatures and the potential to leverage already existing components in the industry. Because these systems utilize renewable electricity to supply high-temperature heat, they are particularly suited for industry or energy storage applications, thus prompting the development of various demonstration plants to evaluate their performance and flexibility. Adapting to varying load conditions and swiftly responding to load adjustments represent crucial aspects for advancing such systems. In this context, this study delves into assessing the transient capabilities of Brayton heat pumps during thermal load management. A transient model of an emerging prototype is presented, comprising thermal and volume dynamics of the components. Furthermore, two reference scenarios are examined to assess the transient performance of the system, namely a thermal load alteration due to an abrupt change in the desired heat sink temperature and, secondly, to a sudden variation in the sink mass flow rate. Finally, two control methodologies—motor/compressor speed variation and fluid inventory control—are analyzed in the latter scenario, and a comparative analysis of their effectiveness is discussed. Results indicate that varying the compressor speed allows for a response time in the 8–20 min range for heat sink temperature regulation (first scenario). However, the regulation time is conditioned by the maximum thermal stress sustained by the heat exchangers. In the latter scenario, regulating the compressor speed shows a faster response time than the inventory control (2–5 min vs. 15 min). However, the inventory approach provides higher COPs in part-load conditions and better stability during the transient phase.
The need for storage capacity is continuously increasing due to the progressive penetration of renewable energy sources in the power grids. New storage technologies for large-scale applications are emerging in this context, among which Pumped Thermal Electricity Storage (PTES) is a promising alternative. PTES is based on closed Brayton cycles: a Brayton heat pump is operated in the charging phase, using the off-peak electricity to transfer heat between two reservoirs. A Brayton heat engine is operated between the same reservoirs in the discharging phase, producing electric energy. The purpose of grid-scale storage facilities is to provide flexibility to the grid. Therefore, the proposed technologies must effectively operate in part-load conditions and quickly react when the load must be adjusted. In this study, the transient response of the Brayton PTES technology is studied, with particular emphasis on its off-design operation and control strategy. To this end, a detailed thermodynamic model of the system is developed. Particular attention is given to the sizing of the components relevant to the control. Furthermore, a control strategy suited for the power regulation of closed Brayton cycles, the Inventory Control, is investigated, and implementation is proposed. As it resulted, the system can operate in part-load with negligible performance degradation and is characterized by a rapid transient response. Therefore, Brayton PTES resulted as a promising storage technology for grid-scale applications.
Rotary tables are often used to speed up the acquisition time during the 3D scanning of complex geometries. In order to avoid manual registration of the point clouds acquired with different orientations, automatic algorithms to compensate the rotation were developed. Alternatively, a proper calibration of the rotary axis with respect to the camera system is needed. Several methods are available in the literature, but they only consider a single-axis calibration. In this paper, a method for the simultaneous calibration of both axes of the table is proposed. A checkerboard is attached to the table, and several images with different poses are acquired. An optimization algorithm is then setup to determine the orientation and the locations of the two axes. A metric to assess the calibration quality was also defined by computing the average mean reprojection error. This metric is used to investigate the optimal number and distribution of the calibration poses, demonstrating that the optimum calibration results are achieved when a wider dispersion of the calibration poses is adopted.
19 October 2023 in Swedish Aerospace Conference, FT2025
Among the environmental-friendly technologies recently proposed in the literature, high-temperature heat pumps represent a promising solution to foster the complete penetration of renewables within the power grid. Such systems may be based on closed Brayton cycles and leverage many existing components. As they are meant to provide high-temperature heat while using renewable electricity, their potential field of application ranges from industrial heating to energy storage. Several variants are currently under development to assess the feasibility of such systems in providing flexibility to the electricity grid. To do so, they need to operate in part-load conditions and quickly react when the load must be adjusted. In this regard, this study investigates the transient capabilities of Brayton heat pump technology. To this extent, a detailed transient model of a novel prototype proposed in the literature is presented, accounting for controls, thermal inertia and volume dynamics related to heat exchangers and piping. Furthermore, the model is used to assess the transient performance of the system in response to sudden load variations, which is achieved by adapting the turbomachinery operating velocities. Results show that the system can safely operate in part-load conditions with regulation times compatible with industrial needs.
14 November 2024 in Journal of Engineering for Gas Turbines and Power
High-temperature heat pumps (HTHPs) are becoming increasingly relevant in the industry as they represent a promising solution for decarbonizing industrial heat. These technologies can enable the electrification of industrial processes by exploiting electricity from renewables to provide process heat at temperatures above 250 °C, as in the case of emerging Brayton-based HTHPs. To succeed in this purpose, HTHPs must also ensure operational flexibility, which entails the ability to operate safely under varying loads and promptly respond to fluctuations in demand, while maintaining high efficiencies. Moreover, the ability to provide large flexible electric loads to transmission system operators has the potential to unlock innovative business cases and further promote the use of these systems. Common control strategies for achieving this include employing bypass mechanisms, fluid inventory control, and adjusting turbomachinery rotational speeds. Despite their variety, the simultaneous use of such control strategies is often limited as they may lead to significantly different system behaviors, both in terms of transient and steady performance. In this paper, rotational speed and fluid inventory control are examined from a transient perspective to maintain the desired sink temperature while regulating the thermal load of a novel Brayton-based HTHP. A comprehensive dynamic model of the system is proposed and leveraged to numerically test the two control approaches, aiming to provide insights for forthcoming experimental investigation. Results indicate that rotational speed control leads to negligible sink temperature residuals, while fluid inventory control better preserves the HTHP performances for varying temperature glides.