Panagiotis Stathopoulos

Prof. Panagiotis Stathopoulos


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 December 2018 in Energies
Verified
Journal Article
Open access
PDF file
PSPanagiotis Stathopoulos
Panagiotis Stathopoulos
Conventional gas turbines are approaching their efficiency limits and performance gains are becoming increasingly difficult to achieve. Pressure Gain Combustion (PGC) has emerged as a very promising technology in this respect, due to the higher thermal efficiency of the respective ideal gas turbine thermodynamic cycles. Up to date, only very simplified models of open cycle gas turbines with pressure gain combustion have been considered. However, the integration of a fundamentally different combustion technology will be inherently connected with additional losses. Entropy generation in the combustion process, combustor inlet pressure loss (a central issue for pressure gain combustors), and the impact of PGC on the secondary air system (especially blade cooling) are all very important parameters that have been neglected. The current work uses the Humphrey cycle in an attempt to address all these issues in order to provide gas turbine component designers with benchmark efficiency values for individual components of gas turbines with PGC. The analysis concludes with some recommendations for the best strategy to integrate turbine expanders with PGC combustors. This is done from a purely thermodynamic point of view, again with the goal to deliver design benchmark values for a more realistic interpretation of the cycle.

16 March 2021 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
MAMajid Asli
Majid Asli
PSPanagiotis Stathopoulos
Panagiotis Stathopoulos
CPChristian Oliver Paschereit
Christian Oliver Paschereit
Any outlet restriction downstream of pressure gain combustion (PGC), such as turbine blades, affects its flow field and may cause additional thermodynamic losses. The unsteadiness in the form of pressure, temperature, and velocity vector fluctuations has a negative impact on the operation of conventional turbines. Additionally, experimental measurements and data acquisition present researchers with challenges that have to do mostly with the high temperature exhaust of PGC and the high frequency of its operation. Nevertheless, numerical simulations can provide important insights into PGC exhaust flow and its interaction with turbine blades. In this paper, a rotating detonation combustor (RDC) and a row of nozzle guide vanes have been modeled based on the data from literature and an available experimental setup. Unsteady Reynolds-averaged Navier–Stokes (URANS) simulations were done for five guide vane configurations with different geometrical parameters to investigate the effect of solidity and blade type representing different outlet restrictions on the RDC exhaust flow. The results analyzed the connection between total pressure loss and the vanes solidity and thickness to chord ratio. It is observed that more than 57% of the upstream velocity angle fluctuation amplitude was damped by the vanes. Furthermore, the area reduction was found to be the significant driving factor for damping the velocity angle fluctuations, whether in the form of solidity or thickness on chord ratio increment. This RDC exhaust flow investigation is an important primary step from a turbomachinery standpoint, which provided details of blade behavior in such an unsteady flow field.

2 November 2016 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Open access
PDF file
PSPanagiotis Stathopoulos
Panagiotis Stathopoulos
PKP. Kuhn
P. Kuhn
JWJ. Wendler
J. Wendler
TTT. Tanneberger
T. Tanneberger
STS. Terhaar
S. Terhaar
MAM. Aigner
M. Aigner
It is generally accepted that combustion of hydrogen and natural gas mixtures will become more prevalent in the near future, to allow for a further penetration of renewables in the European power generation system. The current work aims at the demonstration of the advantages of steam dilution, when highly reactive combustible mixtures are used in a swirl-stabilized combustor. To this end, high-pressure experiments have been conducted with a generic swirl-stabilized combustor featuring axial air injection to increase flashback safety. The experiments have been conducted with two fuel mixtures, at various pressure levels up to 9 bar and at four levels of steam dilution up to 25% steam-to-air mass flow ratio. Natural gas has been used as a reference fuel, whereas a mixture of natural gas and hydrogen (10% hydrogen by mass) represented an upper limit of hydrogen concentration in a natural gas network with hydrogen enrichment. The results of the emissions measurements are presented along with a reactor network model. The latter is applied as a means to qualitatively understand the chemical processes responsible for the observed emissions and their trends with increasing pressure and steam injection.

6 July 2020 in Energy Science & Engineering
Verified
Journal Article
Open access
PDF file
PSPanagiotis Stathopoulos
Panagiotis Stathopoulos
Conventional gas turbines are a very mature technology, and performance improvements are becoming increasingly difficult and costly to achieve. Pressure‐gain combustion (PGC) has emerged as a promising technology in this respect, due to the higher thermal efficiency of the respective ideal gas turbine cycles. The current work analyzes two layouts of the Humphrey cycle for gas turbines with pressure‐gain combustion. One layout replicates the classical layout of gas turbine cycles, whereas an alternative one optimizes the use of pressure‐gain combustion by ensuring the operation of the combustor at stoichiometric conditions. In parallel, both cycle layouts are studied with two different fuels—hydrogen and dimethyl ether—to account for differences in combustion specific heat addition and its effect on cycle efficiency. The current work concludes with an attempt to benchmark the maximum losses of a plenum to achieve efficiency parity with the Joule cycle, for a given pressure gain over a PGC combustor. It is found that the cycle layout with stoichiometric combustion results in an increase in thermal efficiency of up to 7 percentage points, compared to the classic cycle architecture. Moreover, the thermal efficiency of the new layout is less sensitive to the turbine inlet temperature, especially at low compressor pressure ratios. The study of the two fuels has shown that the larger mass specific heat addition leads to higher cycle thermal efficiency and should be considered during the fuel choice. Finally, the maximum allowable plenum pressure loss that results to efficiency parity with the Joule cycle has been computed for a given combustor pressure gain. For turbine inlet temperatures above 1500°C, pressure gain above 1.6 would allow for at least 20% relative pressure drop in the plenum. The respective pressure gain becomes considerably higher for lower turbine inlet temperatures.

21 February 2024 in Energies
Verified
Journal Article
Open access
PDF file
MPMatteo Pettinari
Matteo Pettinari
GFGuido Francesco Frate
Guido Francesco Frate
ATA. Phong Tran
A. Phong Tran
JOJohannes Oehler
Johannes Oehler
PSPanagiotis Stathopoulos
Panagiotis Stathopoulos
Lorenzo FerrariLorenzo Ferrari
Lorenzo Ferrari
High-temperature heat pumps are a key technology for enabling the complete integration of renewables into the power grid. Although these systems may come with several variants, Brayton heat pumps are gaining more and more interest because of the higher heat sink temperatures and the potential to leverage already existing components in the industry. Because these systems utilize renewable electricity to supply high-temperature heat, they are particularly suited for industry or energy storage applications, thus prompting the development of various demonstration plants to evaluate their performance and flexibility. Adapting to varying load conditions and swiftly responding to load adjustments represent crucial aspects for advancing such systems. In this context, this study delves into assessing the transient capabilities of Brayton heat pumps during thermal load management. A transient model of an emerging prototype is presented, comprising thermal and volume dynamics of the components. Furthermore, two reference scenarios are examined to assess the transient performance of the system, namely a thermal load alteration due to an abrupt change in the desired heat sink temperature and, secondly, to a sudden variation in the sink mass flow rate. Finally, two control methodologies—motor/compressor speed variation and fluid inventory control—are analyzed in the latter scenario, and a comparative analysis of their effectiveness is discussed. Results indicate that varying the compressor speed allows for a response time in the 8–20 min range for heat sink temperature regulation (first scenario). However, the regulation time is conditioned by the maximum thermal stress sustained by the heat exchangers. In the latter scenario, regulating the compressor speed shows a faster response time than the inventory control (2–5 min vs. 15 min). However, the inventory approach provides higher COPs in part-load conditions and better stability during the transient phase.

16 October 2018 in Energies
Verified
Journal Article
Open access
PDF file
PSPanagiotis Stathopoulos
Panagiotis Stathopoulos
JFJavier Fernandez-Villa
Javier Fernandez-Villa
Thermoelectric generators (TEGs) offer an attractive power generation option. They have no moving parts, are robust and emit no pollutants. The current work explores the integration of high temperature TEGs in gas turbine combustors. The latter have a thermal shield at their inner surface to protect them against high temperatures. This is supplemented by convective and film cooling. This work studies the replacement of the thermal shield with high temperature TEGs and evaluates their techno-economic potential. A gas turbine model is developed and validated to compute the fuel and air flow rate in the combustion chamber. A heat transfer model is subsequently implemented to compute the temperature distribution inside the combustor wall, on which the TEG is constructed. The investment in TEGs is then analyzed for peaker, intermediate load and base load gas turbines. The work concludes with a sensitivity analysis of the investment economic performance. It is concluded that, despite the low power generation, the installation of TEGs makes economic sense, even if their price becomes 50% higher than current estimations. It is also concluded that electricity prices have a much stronger effect on the economic viability of the investment than the price of the generators.