The objective of this work is the design and validation of a directional Vivaldi antenna to detect tumor cells’ electromagnetic waves with a frequency of around 5 GHz. The proposed antenna is 33% smaller than a traditional Vivaldi antenna due to the use of metamaterials in its design. It has an excellent return loss of 25 dB at 5 GHz and adequate radiation characteristics as its gain is 6.2 dB at 5 GHz. The unit cell size of the proposed metamaterial is 0.058λ × 0.054λ at the operation frequency of 5 GHz. The proposed antenna was designed and optimized in CST microwave software, and the measured and simulated results were in good agreement. The experimental study demonstrates that an array composed with the presented antennas can detect the existence of tumors in a liquid breast phantom with positional accuracy through the analysis of the minimum amplitude of S_ii.

A novel methodology is proposed to reliably predict the resonant characteristics of a multipatch backscatter-based radio frequency identification (RFID) chipless tag. An ultra-wideband impulsion radio (UWB-IR)-based reader interrogates the chipless tag with a UWB pulse, and analyzes the obtained backscatter in the time domain. The RFID system consists of a radar cross-section (RCS)-based chipless tag containing a square microstrip patch antenna array in which the chipless tag is interrogated with a UWB pulse by an UWB-IR-based reader. The main components of the backscattered signal, the structural mode, and the antenna mode were identified and their spectral quality was evaluated. The study revealed that the antenna-mode backscatter includes signal carrying information, while the structural mode backscatter does not include any tag information. The simulation findings were confirmed by experimental measurements obtained in an anechoic chamber environment using a 6-bit multipatch chipless RFID tag. Finally, the novel technique does not use calibration tags and can freely orient tags with respect to the reader.

In this paper, a compact multi-split-ring resonator-based antenna is presented for wireless applications. The proposed antenna integrates multiple resonators to achieve multiband operation, where each resonator corresponds to a specific frequency band. A theoretical analysis is conducted to model the equivalent circuit of the proposed antenna, followed by an analytical study to calculate the resonant frequency of each resonator. By integrating these resonators, the proposed antenna achieves a compact size of 23 × 24 × 1.6 mm³ (0.19 × 0.2 × 0.01λ³), resulting in a size reduction of 81.6% compared to a conventional patch antenna, while maintaining gain, improving bandwidth, and providing excellent impedance matching. The proposed antenna covers the 2.4–2.8 GHz (14.55%), 3.25–3.75 GHz (14.28%) and 4.5–7.84 GHz (54.13%) frequency bands, providing acceptable gains of 1.5 dBi, 2 dBi and 3.2 dBi, respectively. The antenna was designed with CST, its performance was verified with HFSS simulations and it was validated with an equivalent circuit in ADS. Finally, the antenna was fabricated to confirm the accuracy and reliability of the simulation results, and it was found that the measurements agreed well with the simulations. This multiband functionality, combined with a compact form factor and simple feed line, makes the antenna cost-effective, easy to manufacture and suitable for various wireless communication applications, including 5G sub-6 GHz mid-band (2.5/3.5/5/5 GHz), RFID (2.45/5.8 GHz), WiMAX (2.4/3.5/5.8 GHz), Wi-Fi 5/6/6E (2.4/5/6 GHz) and WLAN (5.2/5.8 GHz).

In this paper, a new planar inverted-F antenna is presented for GNSS applications and the DCS band. The proposed antenna structure is based on capacitive slots that achieve multiband behavior. The antenna has two resonators of dimensions (31mm×17mm×0.35mm) and (20.5mm×17.5mm× 0.35mm), a ground plane (60mm×17.5mm×0.35mm) and 6.5mm height. A prototype was implemented and good agreement was noticed between the simulation and test results, indicating three resonant frequencies, namely 1.176GHz, 1.8GHz and 2.8GHz. Radiation characteristics and diversity performance of the proposed structure is presented with detail.

This chapter intends to deal with the challenging field of communication systems known as reconfigurable radio-frequency systems. Mainly, it will present and analyze the design of different reconfigurable components based on radio-frequency microelectromechanical systems (RF MEMS) for different applications. This chapter will start with the description of the attractive properties that RF MEMS structures offer, giving flexibility in the RF systems design, and how these properties may be used for the design of reconfigurable RF MEMS-based devices. Then, the chapter will discuss the design, modeling, and simulation of reconfigurable components based on both theoretical modeling and well-known electromagnetic computing tools such as ADS, CST-MWS, and HFSS to evaluate the performance of such devices. Finally, the chapter will deal with the design and performance assessment of RF MEMS-based devices. Non-radiating devices, such as phase shifter and resonators, which are very important components in the hardware RF boards, will be addressed. Also, three types of frequency reconfigurable antennas, for the three different applications (radar, satellite, and wireless communication), will be proposed and evaluated. From this study, based on theoretical design and electromagnetic computing evaluation, it has been shown that RF MEMS-based devices can be an enabling solution in the design of the multiband reconfigurable radio-frequency devices.