Hydrogen energy is regarded as an ideal solution for addressing climate change issues and an indispensable part of future integrated energy systems. The most environmentally friendly hydrogen production method remains water electrolysis, where the electrolyzer constructs the physical interface between electrical energy and hydrogen energy. However, few articles have reviewed the electrolyzer from the perspective of power supply topology and control. This review is the first to discuss the positioning of the electrolyzer power supply in the future integrated energy system. The electrolyzer is reviewed from the perspective of the electrolysis method, the market, and the electrical interface modelling, reflecting the requirement of the electrolyzer for power supply. Various electrolyzer power supply topologies are studied and reviewed. Although the most widely used topology in the current hydrogen production industry is still single-stage AC/DC, the interleaved parallel LLC topology constructed by wideband gap power semiconductors and controlled by the zero-voltage switching algorithm has broad application prospects because of its advantages of high power density, high efficiency, fault tolerance, and low current ripple. Taking into account the development trend of the EL power supply, a hierarchical control framework is proposed as it can manage the operation performance of the power supply itself, the electrolyzer, the hydrogen energy domain, and the entire integrated energy system.
30 April 2025 in IEEE Transactions on Power Electronics
The Quasi-Square-Wave (QSW) PWM-modulated Modular Multilevel Converter (MMC) offers the advantages of reduced submodule capacitance and arm inductance, making it a promising technology for variable-speed motor drive applications. This article presents an analytical investigation into the sizing requirements for arm inductors and submodule capacitors in the QSW-PWM-modulated MMC. In addition, an alternative switching sequence is proposed to recover arm inductor energy, effectively eliminating oscillations and ripple current while further reducing voltage variation. The proposed control strategy simplifies hardware requirements by limiting control to steady-state voltage regulation, reducing reliance on high-frequency current control. Simulations and experiments conducted on a scaled test rig validate the proposed switching sequence, and verify the reduced capacitor voltage variation achieved through the proposed control strategy.
The modular multilevel DC–DC transformer (MMDCT) provides a reliable solution to overcome the challenges of conventional dual‐active‐bridge converters in terms of power semiconductors ratings and dv/dt stress on transformer coupling windings. An alternative modulation method, quasi‐square‐wave, was proposed to reduce the cell capacitance of modular multilevel bridges. However the application of quasi‐square‐wave modulation is found to result in underdamped switching transients and losses when resetting energy stored in arm inductance. This paper presents a detailed transient analysis of MMDCT arm insertion based on an equivalent circuit, which contributes to a more accurate component sizing and gives voltage estimation for individual half‐bridge submodules. Additionally, a revised switching sequence is proposed to recover this inductor energy and lower the oscillation‐related losses. Simulated and experimental results from a scaled test rig of MMDCT are implemented and validate the proposed component sizing and switching sequence, indicating that the converter efficiency can be improved under revised switching sequence. Finally, a silicon carbide based, high‐frequency MMDCT is proposed and simulated.
17 December 2025 in IEEE Transactions on Power Electronics
Extending the use of dc–dc converters, such as the dual active bridge (DAB) to high voltage applications, will require voltage sharing among series-connected power devices. Initial solutions used snubber capacitors to limit voltage rise and balance the turn-off voltage. However, this mechanism is not viable at low currents, which leads to high capacitor discharge currents. The quasi-square-wave modular multilevel dc–dc converter (QSW-MMC) has been proposed as an option for high voltage DAB converters. This circuit employs an additional switch in series with the capacitor, which acts as a controlled voltage clamp. This avoids problems at low loading but loses the benefit of switching loss reduction at high currents. In this article, a dual-mode operation based on the QSW-MMC is proposed, which actively controls the auxiliary switch to use the submodule capacitor as a clamping component at low currents and as a snubber component at high currents. In addition, the presented control strategy can achieve smooth transitions between two modes. Finally, simulation and experimental results from a scaled test rig validate the efficiency improvement achieved by the proposed dual-mode operation.
22 December 2023 in IEEE Power Electronics Magazine
The micro-modular multilevel converter ( $\mu $ MMC) concept proposes a benchtop-scale, low-voltage, open-source, and affordable hardware prototype of a modular multilevel converter (MMC) intended for research and teaching applications. The $\mu $ MMC ( $\mu $ originates from its rating being approximately one millionth of usual transmission-scale MMCs) aims to provide a solution to break the barrier from theory to practice, thanks to its all-integrated eight full-bridge (FB) submodules (SM) in a $10\times 10$ cm printed circuit board (PCB) with a local microcontroller able to communicate with an external master controller. The electronics is rated for a 30 V dc bus voltage as typically found in traditional lab power supplies, providing both convenience and safety. This structure allows a lot of flexibility in terms of testing converter topology and control architectures. This article details the setup process of the $\mu $ MMC into a 3-phase inverter to demonstrate its versatility and potential as a teaching and research tool.